ade7953 Analog Devices, Inc., ade7953 Datasheet - Page 23
![no-image](/images/no-image-200.jpg)
ade7953
Manufacturer Part Number
ade7953
Description
Single Phase, Multifunction Metering Ic With Neutral Current Measurement Ade7953
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADE7953.pdf
(68 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ade7953ACPZ
Manufacturer:
Samsung
Quantity:
7 040
Part Number:
ade7953ACPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ade7953ACPZ-RL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
ACTIVE POWER CALCULATION
Power is defined as the rate of energy flow from the source to
the load. It is defined as the product of the voltage and current
waveforms. The resulting waveform is called the instantaneous
power signal and is equal to the rate of energy flow at every
instant of time. The unit of power is the watt or joules/sec.
where:
V is the rms voltage.
I is the rms current.
The average power over an integral number of line cycles (n)
is given by the expression in Equation 7.
where:
P is the active or real power.
T is the line cycle period.
The active power is equal to the dc component of the instanta-
neous power signal (P(t) in Equation 5). The active power is
therefore equal to VI. This relationship is used to calculate active
power in the ADE7953. Figure 44 illustrates this concept.
0x0 0000
VRMS
IRMS
×
P(t) = V(t) × I(t)
P(t) = VI − VI × cos(2ω t)
V(t)
I(t)
P
=
=
INSTANTANEOUS
POWER SIGNAL
=
nT
1
I(t) = √2 × IRMS × sin(ωt)
CURRENT
CHANNEL
VOLTAGE
CHANNEL
V(t) = √2 × VRMS × sin(ωt)
A OR B
2
2
nT
∫
0
×
×
P
I
V
Figure 44. Active Power Calculation
) (
t
×
PHCALx
×
dt
sin(
sin(
=
VI
ωt
ωt
P(t) = VRMS × IRMS – VRMS × IRMS × cos(2ωt)
)
xIGAIN
)
VGAIN
HPF
HPF
INSTANTANEOUS
ACTIVE POWER SIGNAL:
VRMS × IRMS
INTEGRATOR
DIGITAL
Figure 45. Active Energy Signal Chain
Rev. 0 | Page 23 of 68
(3)
(4)
(5)
(6)
(7)
LPF2
ACTIVE POWER
SIGNAL
xWGAIN
The signal chain for the active power and energy calculations in
the ADE7953 is shown in Figure 45. The instantaneous power
signal P(t) is generated by multiplying the current and voltage
signals. The dc component of the instantaneous power signal
is then extracted by LPF2 (low-pass filter) to obtain the active
power information. Because LFP2 does not have an ideal “brick
wall” frequency response, the active power signal has some
ripple associated with it. This ripple is sinusoidal and has a
frequency equal to twice the line frequency. Because the ripple
is sinusoidal in nature, it is removed when the active power
signal is integrated to compute the active energy (see the Active
Energy Calculation section).
The ADE7953 computes the active power simultaneously on
Current Channel A and Current Channel B and stores the
resulting measurements in the AWATT (Address 0x212 and
Address 0x312) and BWATT (Address 0x213 and Address 0x313)
registers, respectively. With full-scale inputs, the expected
reading in the AWATT and BWATT registers is approximately
5,000,000 LSBs (decimal).
The active power measurements are taken over a bandwidth of
1.23 kHz and include the effects of any harmonics within that
range. The active power registers are updated at a rate of 6.99 kHz
and can be read using the waveform sampling mode (see the
Instantaneous Powers and Waveform Sampling section).
SIGN OF ACTIVE POWER CALCULATION
The active power measurement in the ADE7953 is a signed calcu-
lation. If the phase differential between the current and voltage
waveforms is more than 90°, the power is negative. Negative
power indicates that energy is being injected back into the grid.
The ACCMODE register (Address 0x201 and Address 0x301)
includes two sign indication bits that show the sign of the active
power of Current Channel A (APSIGN_A) and Current
Channel B (APSIGN_B). See the Sign Indication section for
more information.
xWATTOS
+
+
48
FIXED INTERNAL
ACCUMULATION
THRESHOLD
INTERNAL
0
23
AENERGYx
ADE7953
0