cp3bt26y98nepx National Semiconductor Corporation, cp3bt26y98nepx Datasheet - Page 135
cp3bt26y98nepx
Manufacturer Part Number
cp3bt26y98nepx
Description
Reprogrammable Connectivity Processor With Bluetooth-r, Usb, And Can Interfaces
Manufacturer
National Semiconductor Corporation
Datasheet
1.CP3BT26Y98NEPX.pdf
(280 pages)
- Current page: 135 of 280
- Download datasheet (5Mb)
19.10.6 CAN Global Configuration Register (CGCR)
The CAN Global Configuration Register (CGCR) is a 16-bit
wide register used to:
! Enable/disable the CAN module.
! Configure the BUFFLOCK function for the message buff-
! Enable/disable the time stamp synchronization.
! Set the logic levels of the CAN Input/Output pins, CAN-
! Choose the data storage direction (DDIR).
! Select the error interrupt type (EIT).
! Enable/disable diagnostic functions.
CANEN
CTX
CRX
BUFFLOCK The Buffer Lock bit configures the buffer lock
IGNACK LO DDIR
15
er 0..14.
RX and CANTX.
Reserved
7
6
12
The CAN Enable bit enables/disables the
CAN module. When the CAN module is dis-
abled, all internal states and the TEC and
REC counter registers are cleared. In addition
the CAN module clock is disabled. All CAN
module control registers and the contents of
the object memory are left unchanged. Soft-
ware must make sure that no message is
pending for transmission before the CAN
module is disabled.
0 – CAN module is disabled.
1 – CAN module is enabled.
The Control Transmit bit configures the logic
level of the CAN transmit pin CANTX.
0 – Dominant state is 0; recessive state is 1.
1 – Dominant state is 1; recessive state is 0.
The Control Receive bit configures the logic
level of the CAN receive pin CANRX.
0 – Dominant state is 0; recessive state is 1.
1 – Dominant state is 1; recessive state is 0.
function. If this feature is enabled, a buffer will
be locked upon a successful frame reception.
The buffer will be unlocked again by writing
RX_READY in the buffer status register, i.e.,
after reading data.
0 – Lock function is disabled for all buffers.
1 – Lock function is enabled for all buffers.
5
EIT DIAGEN INTERNAL LOOPBACK
11
PEN
TST
4
10
R/W
R/W
LOCK
0
0
BUFF
3
CRX CTX CANEN
9
2
1
8
0
135
TSTPEN
DDIR
The Time Sync Enable bit enables or disables
the time stamp synchronization function of the
CAN module.
0 – Time synchronization disabled. The Time
1 – Time synchronization enabled. The Time
The Data Direction bit selects the direction the
data bytes are transmitted and received. The
CAN module transmits and receives the CAN
Data1 byte first and the Data8 byte last
(Data1, Data2,...,Data7, Data8). If the DDIR
bit is clear, the data contents of a received
message is stored with the first byte at the
highest data address and the last data at the
lowest data address (see Figure 64). The
same applies for transmitted data.
0 – First byte at the highest address, subse-
1 – First byte at the lowest address, subse-
Stamp counter value is not reset upon re-
ception or transmission of a message to/
from buffer 0.
Stamp counter value is reset upon recep-
tion or transmission of a message to/from
buffer 0.
quent bytes at lower addresses.
quent bytes at higher addresses.
www.national.com
Related parts for cp3bt26y98nepx
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal Bus Transceiver
Manufacturer:
National Semiconductor Corporation
Datasheet: