tja1054 NXP Semiconductors, tja1054 Datasheet
tja1054
Available stocks
Related parts for tja1054
tja1054 Summary of contents
Page 1
... DATA SHEET TJA1054 Fault-tolerant CAN transceiver Product specification Supersedes data of 2001 Nov 20 INTEGRATED CIRCUITS 2004 Mar 23 ...
Page 2
... The TJA1054T is pin and downwards compatible with the PCA82C252T and the TJA1053T. This means that these two devices can be replaced by the TJA1054T with retention of all functions. The most important improvements of the TJA1054 with respect to the PCA82C252 and the TJA1053 are: ...
Page 3
... BAT no time limit 5 BAT no time limit CANH CANL between 10% and 90 nF; see Fig.5 between 10% and 90 nF; see Fig.5 3 Product specification TJA1054 MIN. TYP. MAX. 4.75 5.25 0.3 + +40 1.4 1 ...
Page 4
... TXD TIMER ERR RXD 13 GND 2004 Mar 23 BAT 14 TEMPERATURE WAKE-UP PROTECTION STANDBY CONTROL DRIVER TJA1054 FAILURE DETECTOR PLUS WAKE-UP PLUS TIME-OUT RECEIVER Fig.1 Block diagram. 4 Product specification TJA1054 RTL 11 CANH 12 CANL 8 RTH FILTER FILTER MGL421 ...
Page 5
... LOW-level CAN bus line GND 13 ground BAT 14 battery supply voltage handbook, halfpage 2004 Mar 23 DESCRIPTION INH 1 14 BAT TXD 2 13 GND RXD 3 12 CANL 4 TJA1054T 11 ERR CANH STB RTL 7 8 WAKE RTH MGL422 Fig.2 Pin configuration. 5 Product specification TJA1054 ...
Page 6
... Philips Semiconductors Fault-tolerant CAN transceiver FUNCTIONAL DESCRIPTION The TJA1054 is the interface between the CAN protocol controller and the physical wires of the CAN bus (see Fig.7 primarily intended for low-speed applications 125 kBaud, in passenger cars. The device provides differential transmit capability to the CAN bus and differential receive capability to the CAN controller ...
Page 7
... BAT notes 1 and 5 error flag no error flag 7 Product specification PIN RXD LOW HIGH wake-up interrupt signal; notes 1 2 and 3 wake-up interrupt signal; notes 1 2 and 3 dominant recessive received data received data TJA1054 PIN RTL SWITCHED TO V BAT V BAT V CC ...
Page 8
... All other parts of the device will continue to operate. The pins CANH and CANL are protected against electrical transients which may occur in an automotive environment. . h(sleep) 8 Product specification TJA1054 = 5 BAT while pin EN or CANH CANL active. ...
Page 9
... Transitions to normal mode clear the internal wake-up: interrupt and battery fail flag are cleared. (5) Transitions to sleep mode: pin INH is deactivated. 2004 Mar 23 POWER-ON STANDBY 10 (4) STANDBY 00 of the transceiver is active. Fig.3 Mode control. 9 Product specification GOTO (5) SLEEP 01 SLEEP 00 MBK949 TJA1054 . CC ...
Page 10
... BAT 15 0.3 V BAT 0.3 V BAT 0.3 V BAT 500 16000 500 16000 40 +150 55 +150 2 +2 175 +175 = amb limits the allowable combinations CONDITIONS VALUE in free air 120 in free air 40 TJA1054 MAX. UNIT where th(vj-a) UNIT K/W K/W ...
Page 11
... V BAT low power modes power-on flag set power-on flag not set low power modes BAT WAKE INH Product specification TJA1054 MIN. TYP. MAX. 4.75 5.25 2.75 4 0.3 +40 5 BAT 10 30 ...
Page 12
... TXD low power modes CANL BAT normal operating mode 1.5 low power modes 1.1 normal operating mode 6 4.75 to 5.25 V 1.32V CC low power modes 2.5 low power modes 1.1 12 Product specification TJA1054 MIN. TYP. MAX 0.4 1 3.2 3.9 0.8 5 3.2 2.9 0.64V 0.58V 0.2 ...
Page 13
... I < low power modes low power modes; 1. RTL normal operating mode and failures 4, 6 and 7 normal operating mode and failures 3 and 3a 155 13 Product specification TJA1054 MIN. TYP. MAX. 1.4 1.7 1.85 0.34V 0.37V 3.3 3.45 0.66V 0.69V ...
Page 14
... V BAT note 4 low power modes; V BAT for wake-up after receiving a falling or rising edge; note 4 normal operating mode failures 3 and 3a failures 4, 6 and 7 low power modes; V BAT failures 3 and 3a failures 4 and 7 14 Product specification TJA1054 MIN. TYP. MAX. 0.35 0.60 0.2 0.3 0.75 1.5 1 1.75 0.85 1.4 1.1 1.7 1 ...
Page 15
... V failures 3, 3a, 4 and 7 normal operating mode and failures and 6a; pin ERR becomes LOW failures and 6a t PD(L) Fig.4 Timing diagram. 15 Product specification TJA1054 MIN. TYP. MAX. 0.3 1 125 750 = 12 V BAT 0.3 1 ...
Page 16
... CANL 12 5 TJA1054 CANH 11 6 RTL GND ERR Fig.6 Test circuit for automotive transients. 16 Product specification RTH 8 CANL 12 C2 CANH 11 RTL ERR MGL423 125 1 nF 511 1 nF GENERATOR 1 nF 511 1 nF 125 MGL426 TJA1054 ...
Page 17
... CAN CONTROLLER CTX0 CRXO Px.x Px.x TXD RXD STB ERR TJA1054 CAN TRANSCEIVER RTH CANH CANL CAN BUS LINE Fig.7 Application diagram. 17 Product specification V BAT BATTERY Px.x EN INH 1 BAT 100 nF GND 13 9 RTL TJA1054 MGL425 ...
Page 18
... TJA1054U 2700 m Fig.8 Bonding pad locations. 18 Product specification TJA1054 (1) COORDINATES x y 106 317 111 169 750 111 1347 111 2248 103 2521 240 2521 381 2550 1269 2359 1840 1886 ...
Page 19
... REFERENCES JEDEC JEITA MS-012 19 Product specification detail 1.0 0.7 1.05 0.25 0.25 0.4 0.6 0.039 0.028 0.041 0.01 0.01 0.004 0.016 0.024 EUROPEAN PROJECTION TJA1054 SOT108 ( 0.7 0 0.028 0.012 ISSUE DATE 99-12-27 03-02-19 ...
Page 20
... Use a low voltage ( 2.5 mm less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 20 Product specification TJA1054 ...
Page 21
... The appropriate soldering profile can be provided on request. 9. Hot bar or manual soldering is suitable for PMFP packages. 2004 Mar 23 (1) (3) , TFBGA, (8) 21 Product specification SOLDERING METHOD WAVE REFLOW not suitable suitable (4) not suitable suitable suitable suitable (5)(6) not recommended suitable (7) not recommended suitable not suitable not suitable TJA1054 (2) ...
Page 22
... This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). 22 Product specification TJA1054 DESCRIPTION DEFINITION ...
Page 23
... Semiconductors assumes no liability for device functionality or performance of the die or systems after third party sawing, handling, packing or assembly of the die the responsibility of the customer to test and qualify their application in which the die is used. 23 Product specification TJA1054 These products are not ...
Page 24
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited ...