mic3002 Micrel Semiconductor, mic3002 Datasheet - Page 56
mic3002
Manufacturer Part Number
mic3002
Description
Mic3002 Fom Management Ic With Internal Calibration
Manufacturer
Micrel Semiconductor
Datasheet
1.MIC3002.pdf
(65 pages)
Micrel, Inc.
July 2007
Default Value
Serial Address
Byte Address
A valid OEM password is required for access to this register. This register is non-volatile and will be maintained through power
and reset cycles.
D[7]
D[6]
D[5:4]
D[3]
D[2]
D[1]
D[0]
Default Value
Serial Address
Byte Address
This four-byte field is the password required for access to the OEM area of the MIC3002’s memory and registers. The byte at
address 12 (0C h ) is the most significant byte. This field is compared to the four-byte OEMPW field at serial address A2 h , byte
120 to 123 if OMCFG6-2 = 0, or byte 123 to 126 if OEMCFG6-2 = 1. If the two fields match, access is allowed to the OEM
areas of the MIC3002 non-volatile memory at serial addresses A4 h and A6 h . The OEM password may be set by writing the
new value into OEMPWSET. The new password will not take effect until after a power-on reset occurs or a warm reset is
performed using the RST bit in OEMCFG0. This allows the new password to be verified before it takes effect. These registers
are non-volatile and will be maintained through power and reset cycles. A valid OEM password is required for access to this
register.
Byte
3
2
1
0
read/write
read/write
OEMIM
D[7]
D[7]
Bit
Weight
OEM Password, Most Significant Byte
OEM Password, 2nd Most Significant Byte
OEM Password, 2nd Least Significant Byte
OEM Password, Least Significant Byte
OEMIM
POHE
D[5:4]
SATMSK
TXMSK
IAMSK
DFMSK
read/write
read/write
POHE
D[6]
D[6]
Function
OEM interrupt mask bit
OEM Power-on Hour Meter enable bit
Reserved
APC saturation fault mask bit
High TX optical power fault mask bit
Bias current high alarm mask bit
Diode fault mask bit
read/write
reserved
D[5]
D[5]
OEM Password Setting (OEMPWSET)
0000 0000 b = 00 h
A6 h
11 = 0B h
0000 0000 b = 00 h
A6 h
12 - 15 = 0C h - 0F h ; 0C h = MSB
read/write
reserved
Fault Mask (FLTMSK)
D[4]
D[4]
Operation
1 = masked; 0 = enabled; Read/write; non-volatile.
1 = enabled; 0 = disabled; Read/write; non-volatile.
Always write as zero; reads undefined.
1 = masked; 0 = enabled; Read/write; non-volatile.
1 = masked; 0 = enabled; Read/write; non-volatile.
1 = masked; 0 = enabled; Read/write; non-volatile.
1 = masked; 0 = enabled; Read/write; non-volatile.
read/write
read/write
SATMSK
56
D[3]
D[3]
read/write
read/write
TXMSK
D[2]
D[2]
hbwhelp@micrel.com
read/write
read/write
IAMSK
D[1]
D[1]
or (408) 955-1690
read/write
read/write
M9999-073107-B
DFMSK
D[0]
D[0]
MIC3002