at42qt1481 ATMEL Corporation, at42qt1481 Datasheet - Page 29
at42qt1481
Manufacturer Part Number
at42qt1481
Description
48-key Qmatrix Ic
Manufacturer
ATMEL Corporation
Datasheet
1.AT42QT1481.pdf
(74 pages)
- Current page: 29 of 74
- Download datasheet (993Kb)
9621B–AT42–06/11
Device Status: This byte is a collection of general status bits, see
Table 4-1.
Bit 6: Set if calibration failed on any enabled key.
Bit 5: Set if an FMEA error was detected during operation. This flag will be set during calibration
after reset, and should be ignored until calibration has completed. See
Bit 4: Set if a mismatch occurs with the setups CRC. If this happens, it is recommended that the
QT1481 be reset, which forces the setups to be recovered from internal Flash. If a reset does
not cure the problem, the setups block should be reloaded (see
the QT1481 reset again. The time required to recompute the Setups CRC and report an error is
a maximum of 1150 ms.
Bit 3: Set if there was a mains sync error, for example there was no Sync signal detected within
the allotted 100 ms amount of time. See
necessarily fatal to operation, however the QT1481 operates very slowly and may suffer from
noise problems if the sync feature is required for noise reasons.
Bit 2: Reports that an enabled key has a low signal reference value, lower than the user-settable
LSL value (see
Bit 1: Set if any key is in the process of calibrating.
Touch Overview: This byte gives an initial indication of the number of keys touched as well as
the number of the first touched key, as follows:
Table 4-2.
Bits 7 – 6: A 2-bit unsigned value indicating the number of touched keys. A value of three
indicates that three or more keys are touched.
Bit
7 – 6
5 – 0
Bit
7
6
5
4
3
2
1
0
Device Status Bits
Key Touch Information
Section 5.18 on page
Description
Reserved
1 = Calibration has failed on an enabled key
1 = FMEA failure detected
1 = Setups CRC mismatch
1 = Mains sync error
1 = LSL failure
1 = Any key in calibration
Reserved
Description
0 = No touched keys
1 = 1 key in detect
2 = 2 keys in detect
3 = 3 or more keys in detect
Number of 1st key declaring detect (0 – 47)
48).
Section 5.14 on page
Section 5.31 on page
Table 4-1 on page
46. This condition is not
Section 2.17 on page
AT42QT1481
29.
53) and
16.
29
Related parts for at42qt1481
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: