lmp7701max National Semiconductor Corporation, lmp7701max Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
lmp7701max
Manufacturer Part Number
lmp7701max
Description
Precision, Cmos Input, Rrio, Wide Supply Range Amplifiers
Manufacturer
National Semiconductor Corporation
Datasheet
1.LMP7701MAX.pdf
(22 pages)
www.national.com
V
I
I
SR
GBW
THD+N
e
i
n
O
S
Symbol
n
O
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics
Tables.
Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-
Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
Note 3: The maximum power dissipation is a function of T
P
Note 4: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating
of the device such that T
T
Note 5: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
Note 6: Limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlations using the Statistical Quality
Control (SQC) method.
Note 7: This parameter is guaranteed by design and/or characterization and is not tested in production.
Note 8: Positive current corresponds to current flowing into the device.
Note 9: The short circuit test is a momentary test.
Note 10: The number specified is the slower of positive and negative slew rates.
A
D
.
= (T
J(MAX)
Output Swing High
Output Swing Low
Output Short Circuit Current
(Notes 3, 9)
Supply Current
Slew Rate (Note 10)
Gain Bandwidth Product
Total Harmonic Distortion + Noise
Input-Referred Voltage Noise
Input-Referred Current Noise
– T
A
)/ θ
JA
. All numbers apply for packages soldered directly onto a PC Board.
J
= T
Parameter
A
. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self-heating where T
J(MAX)
R
LMP7701
R
LMP7702/LMP7704
R
LMP7701
R
LMP7702/LMP7704
R
LMP7701
R
LMP7702/LMP7704
R
LMP7701
R
LMP7702/LMP7704
Sourcing V
V
Sourcing V
V
Sinking V
V
LMP7701
LMP7702
LMP7704
A
10% to 90%
f = 1 kHz, A
f = 1 kHz
f = 100 kHz
L
L
L
L
L
L
L
L
IN
IN
IN
V
= 2 kΩ to 0V
= 2 kΩ to 0V
= 10 kΩ to 0V
= 10 kΩ to 0V
= 2 kΩ to 0V
= 2 kΩ to 0V
= 10 kΩ to 0V
= 10 kΩ to 0V
= +1, V
, θ
= 100 mV (LMP7701)
= 100 mV (LMP7702/LMP7704)
= −100 mV
JA
. The maximum allowable power dissipation at any ambient temperature is
O
O
O
O
= 0V
V
Conditions
= 9 V
= 0V
= 0V
= 1, R
6
PP
L
= 10 kΩ
(Note 6)
Min
50
35
48
33
50
35
(Note 5)
0.790
0.02
Typ
1.7
3.2
1.1
2.5
90
90
40
40
90
90
40
40
86
86
84
9
1
(Note 6)
Max
150
170
180
290
100
150
130
150
180
290
110
1.1
1.3
2.1
2.5
4.2
5.0
80
80
50
60
60
from V
from V
nV/
fA/
Units
V/μs
MHz
mV
mV
mA
mA
%
J
>
+
–