hc5513b Intersil Corporation, hc5513b Datasheet
hc5513b
Available stocks
Related parts for hc5513b
hc5513b Summary of contents
Page 1
... This process feature makes the HC5513 ideally suited for use in harsh outdoor environments. Part Number Information PART TEMP. RANGE o NUMBER ( C) PACKAGE HC5513BIP - PDIP Block Diagram RING RELAY RINGRLY DT RING TRIP DETECTOR DR TIP ...
Page 2
Absolute Maximum Ratings Operating Temperature Range . . . . . . . . . . . . . . . . - ≤ T ≤ 85 Power Supply (- Supply Voltage V to GND ...
Page 3
Electrical Specifications T = -40 A 41.2kΩ, R PARAMETER LONGITUDINAL CURRENT LIMIT (TIP/RING) Off-Hook (Active) = ∞ On-Hook (Standby 368Ω TIP RSN A 5 39kΩ -5V 2.16µF A RING R DC 368Ω 6 ...
Page 4
Electrical Specifications T = -40 A 41.2kΩ, R PARAMETER 2-Wire Return Loss C = 20nF HP TIP IDLE VOLTAGE Active Standby RING IDLE VOLTAGE Active Standby ...
Page 5
Electrical Specifications T = -40 A 41.2kΩ, R PARAMETER INSERTION LOSS 2-Wire to 4-Wire 4-Wire to 2-Wire GAIN TRACKING (Ref = -10dBm, at 1.0kHz) 2-Wire to 4-Wire 2-Wire to 4-Wire 4-Wire to 2-Wire 4-Wire to 2-Wire GRX = ((V - ...
Page 6
Electrical Specifications T = -40 A 41.2kΩ, R PARAMETER Tip/Ring Current Difference - Trigger Tip/Ring Current Difference - Reset Hysteresis TIP 600Ω TR RING RSN 6 19 FIGURE 10. IDLE CHANNEL NOISE RING ...
Page 7
Electrical Specifications T = -40 A 41.2kΩ, R PARAMETER SUPPLY CURRENTS (V = -28V) BAT I , On-Hook On-Hook On-Hook BAT PSRR 4-Wire Port 4-Wire ...
Page 8
Circuit Operation and Design Information The HC5513 is a current feed voltage sense Subscriber Line Interface Circuit (SLIC). This means that for short loop applications the SLIC provides a programed constant current to the tip and ring terminals while sensing ...
Page 9
R SG programmable saturation guard reference voltage: 5 • 12 ------------------ SGREF R SG where Saturation Guard reference voltage. SGREF R = Saturation Guard programming resistor. SG When ...
Page 10
Substituting in Equation 12 for ------------ - + 1000 Therefore • 1000 Z – Equation 16 can now be used to match the ...
Page 11
The value then • ----------- = – Where V /V equals 4-4 Therefore ------------ - + ...
Page 12
RING CASE 1 CASE 2 CASE METALLIC LONGITUDINAL LONGITUDINAL ¨ ¨ Æ METALLIC LONGITUDINAL LONGITUDINAL Æ ¨ Æ FIGURE 18. LOOP CURRENT AND GROUND KEY DETECTORS A filter capacitor ( parallel ...
Page 13
The function of this circuit is to maintain the tip and ring voltages symmetrically around V /2, in the presence of BAT longitudinal currents. The differential transconductance amplifiers G and G accomplish this by sourcing or sinking T R the ...
Page 14
AC-DC Separation Capacitor, C The high pass filter capacitor connected between pins HPT and HPR provides the separation between circuits sensing tip to ring DC conditions and circuits processing AC signals. A 10nf C will position the low end frequency ...
Page 15
Notes 2. Overload Level ...
Page 16
Two-Wire to Four-Wire (Metallic to V 2-wire to 4-wire (metallic voltage gain is computed TX using the following equation 0dBm0 Figure 7. ...
Page 17
Pin Descriptions (Continued) PDIP SYMBOL 12 E1 TTL compatible logic input. The logic state conjunction with the logic state of C1 determines which detector is gated to the DET output TTL compatible logic input. Enables ...
Page 18
Pinout 18 HC5513 HC5513 (PDIP) TOP VIEW HPT 1 22 HPR RSN TIPX 5 18 AGND RINGX BGND ...
Page 19
Application Circuit BAT PTC R F1 TIP D 3 PTC NOTE 31 RING Surgector RINGING +5V RELAY 90V ) BAT RMS ...
Page 20
... Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use ...