ada4930-1 Analog Devices, Inc., ada4930-1 Datasheet - Page 24
![no-image](/images/no-image-200.jpg)
ada4930-1
Manufacturer Part Number
ada4930-1
Description
Ultralow Noise Drivers For Low Voltage Adcs Ada4930-1/ada4930-2
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADA4930-1.pdf
(28 pages)
ADA4930-1/ADA4930-2
HIGH PERFORMANCE ADC DRIVING
The ADA4930-1/ADA4930-2 provide excellent performance in
3.3 V single-supply applications.
The circuit shown in Figure 59 is an example of the ADA4930-1
driving an AD9255, 14-bit, 80 MSPS ADC that is specified to
operate with a single 1.8 V supply. The performance of the ADC
is optimized when it is driven differentially, making the best use of
the signal swing available within the 1.8 V supply. The ADA4930-1
performs the single-ended-to-differential conversion, common-
mode level shifting, and buffering of the driving signal.
The ADA4930-1 is configured for a single-ended input to differential
output with a gain of 2 V/V. The 84.5 Ω termination resistor, in
parallel with the single-ended input impedance of 95.1 Ω, provides
a 50 Ω termination for the source. The additional 31.6 Ω (95 Ω
total) at the inverting input balances the parallel impedance of
the 50 Ω source and the termination resistor that drives the
noninverting input.
The V
and sets the output common mode of the ADA4930-1 at 1 V.
Note that a dc bias must be added to the signal source and its
Thevenin equivalent to the gain resistor on the inverting side
to ensure that the inputs of the ADA4930-1 are kept at or above
the specified minimum input common-mode voltage at all times.
The 0.5 V dc bias at the signal source and the 0.314 V dc bias on the
gain resistor at the inverting input set the inputs of the ADA4930-1
to ~0.48 V dc. With 1 V p-p maximum signal swing at the input,
the ADA4930-1 inputs swing between 0.36 V and 0.6 V.
For a common-mode voltage of 1 V, each ADA4930-1 output
swings between 0.501 V and 1.498 V, providing a 1.994 V p-p
differential output.
OCM
pin is connected to the VCM output of the AD9255
0.5V
50Ω
50Ω
V
1V p-p
V
1V p-p
IN
IN
88.5Ω
84.5Ω
0.314V
64.2Ω
96.2Ω
739Ω
739Ω
63.4Ω
95Ω
Figure 59. Driving an AD9255, 14-Bit, 80 MSPS ADC
Figure 60. Driving an AD9640, 14-Bit, 80 MSPS ADC
3.3V
3.3V
V
V
OCM
OCM
ADA4930-1
+
ADA4930-2
301Ω
301Ω
+
3.3V
301Ω
301Ω
3.3V
Rev. A | Page 24 of 28
33Ω
33Ω
V
30pF
30pF
OCM
A third-order, 40 MHz, low-pass filter between the ADA4930-1
and the AD9255 reduces the noise bandwidth of the amplifier
and isolates the driver outputs from the ADC inputs.
The circuit shown in Figure 60 is an example of ½ of an
ADA4930-2 driving ½ of an AD9640, a 14-bit, 80 MSPS
ADC that is specified to operate with a single 1.8 V supply.
The performance of the ADC is optimized when it is driven
differentially, making the best use of the signal swing available
within the 1.8 V supply. The ADA4930-2 performs the single-
ended-to-differential conversion, common-mode level shifting,
and buffering of the driving signal.
The ADA4930-2 is configured for a single-ended input to differential
output with a gain of 2 V/V. The 88.5 Ω termination resistor, in
parallel with the single-ended input impedance of 114.75 Ω,
provides a 50 Ω termination for the source. The increased gain
resistance at the inverting input balances the 50 Ω source resistance
and the termination resistor that drives the noninverting input.
The V
sets the output common mode of the ADA4930-2 at 1 V.
The 739 Ω resistors between each input and the 3.3 V supply
provide the necessary dc bias to guarantee compliance with the
input common-mode range of the ADA4930-2.
For a common-mode voltage of 1 V, each ADA4930-2 output
swings between 0.501 V and 1.498 V, providing a 1.994 V p-p
differential output.
A third-order, 40 MHz, low-pass filter between the ADA4930-2
and the AD9640 reduces the noise bandwidth of the amplifier
and isolates the driver outputs from the ADC inputs.
168nH
168nH
168nH
168nH
90pF
90pF
OCM
pin is connected to the CML output of the AD9640 and
VIN–
VIN+
VIN–
VIN+
AGND
AVDD
AGND
AVDD
AD9255
AD9640
1.8V
1.8V
DRVDD
DRVDD
VCM
CML
D11 TO
D0
D11 TO
D0