lm6118 National Semiconductor Corporation, lm6118 Datasheet
lm6118
Available stocks
Related parts for lm6118
lm6118 Summary of contents
Page 1
... Total supply current: j ™ (Verti- Output drives 50 load ( j Applications n D/A converters n Fast integrators n Active filters Dual-In-Line Package ( DS010254-3 Order Number LM6118N, LM6218AN or LM6218N See NS Package Number N08E May 1999 Typical 0.2 mV 400 ns 140 V/µs 75 V/µs 17 MHz 5.5 mA ± 1V) DS010254-4 Top View ...
Page 2
Typical Applications Single ended input to differential output = 10 3.2 MHz A V Response = 1.4 MHz ± V 15V S www.national.com DS010254-1 Wide-Band, Fast-Settling 40 V Amplifier PP 2 ...
Page 3
... Operating Temp. Range (Note 2) ± LM6118 Internally Limited LM6218A 500 mW LM6218 ± 0A, unless otherwise specified. Limits with standard type face are for T OUT Typ LM6118 25˚C Limits (Note 6) 0 − 3.5V 0.3 1.5 2.5 V+ − 3. 250 V+ − 3.5V 200 ...
Page 4
Electrical Characteristics Note 3: The inputs are shunted with three series-connected diodes back-to-back for input differential clamping. Therefore differential input voltages greater than about 1.8V will cause excessive current to flow unless limited to less than 10 mA. Note 4: ...
Page 5
Typical Performance Characteristics Total Harmonic Distortion DS010254-34 Output Current Limit DS010254-37 Inverter Settling Time DS010254-40 (Continued) Output Impedance DS010254-35 Supply Current (Both Amplifiers) DS010254-38 Follower Settling Time DS010254-41 5 Output Saturation DS010254-36 Slew Rate DS010254-39 Typical Stability Range DS010254-42 www.national.com ...
Page 6
... Step Response + ± 15V Application Information General The LM6118/LM6218 are high-speed, fast-settling dual op-amps. To insure maximum performance, circuit board lay- out is very important. Minimizing stray capacitance at the in- puts and reducing coupling between the amplifier’s input and output will minimize problems. ...
Page 7
Application Information (Continued) Voltage Follower DS010254-10 = 1000 pF, Small signal MHz For 500 kHz 20 V p-p Inverter DS010254-11 Settling time to 0.01%, 10V Step = 1000 pF, settling time For C ...
Page 8
Application Information * adjust for zero integrator drift (a) Inverting Input Bias Compensation for Integrator Application = + OUT ± 15V, C 0.01 µ Large and small signal B.W. = 1.3 ...
Page 9
Application Information (Continued) Constant-Voltage Crossover Network With 12 dB/Octave Slope Bilateral Current Source = ± V 15V, −10 V 10V S IN Output dynamic range = 10V − OUT = 500 , small signal ...
Page 10
... Instrumentation Amplifier = 10 ± A 15V, All resistors 0.01 Small signal and large signal ( B.W. 800 kHz P-P Schematic Diagram www.national.com (Continued) 150 MHz Gain-Bandwidth Amplifier = 100 ± A 15V, DS010254- Small signal BW 1.5 MHz Large signal BW ( p-p 1/2 LM6118 (Op Amp A) 10 DS010254-20 800 kHz DS010254-21 ...
Page 11
Schematic Diagram (Continued) Bias Circuit 11 DS010254-22 www.national.com ...
Page 12
Physical Dimensions inches (millimeters) unless otherwise noted www.national.com 8-Lead Molded Small Outline Package (M) Order Number LM6218AWM or LM6218WM NS Package Number M14B 12 ...
Page 13
... Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Order Number LM6118N, LM6218AN or LM6218N LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1 ...