lm2902mep National Semiconductor Corporation, lm2902mep Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
lm2902mep
Manufacturer Part Number
lm2902mep
Description
Low Power Quad Operational Amplifiers
Manufacturer
National Semiconductor Corporation
Datasheet
1.LM2902MEP.pdf
(18 pages)
www.national.com
Electrical Characteristics
Note 4: For operating at high temperatures, the LM2902EP must be derated based on a +125˚C maximum junction temperature and a thermal resistance of 88˚C/W
which applies for the device soldered in a printed circuit board, operating in a still air ambient. The dissipation is the total of all four amplifiers — use external resistors,
where possible, to allow the amplifier to saturate of to reduce the power which is dissipated in the integrated circuit.
Note 5: Short circuits from the output to V
current is approximately 40 mA independent of the magnitude of V
dissipation ratings and cause eventual destruction. Destructive dissipation can result from simultaneous shorts on all amplifiers.
Note 6: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP
transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action
on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V
that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value
greater than −0.3V (at 25˚C).
Note 7: The LM2902EP specifications are limited to −40˚C ≤ T
Note 8: "Testing and other quality control techniques are used to the extent deemed necessary to ensure product performance over the specified temperature
range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific
PARAMETRIC testing, product performance is assured by characterization and/or design."
Note 9: V
Note 10: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output
so no loading change exists on the input lines.
Note 11: The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25˚C). The upper end of the
common-mode voltage range is V
Note 12: Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This typically can be
detected as this type of capacitance increases at higher frequencies.
Note 13: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.
Note 14: Human body model, 1.5 kΩ in series with 100 pF.
Note 15: The LM124 within this data sheet’s graphics is referenced because of it’s a similarity to the LM2902, however is not offered in this data sheet.
Short Circuit to Ground
Input Offset Voltage
V
Input Offset Current
I
Input Bias Current
Input Common-Mode
Voltage Range (Note 11)
Large Signal Voltage Gain
Output
Voltage
Swing
Output
Current
OS
V
OS
+
Drift
= +5.0V, unless otherwise stated (Notes 7, 8)
Drift
O
. 1.4V, R
Parameter
S
= 0Ω with V
V
Source
Sink
V
OL
OH
+
− 1.5V (at 25˚C), but either or both inputs can go to +26V without damage, independent of the magnitude of V
+
from 5V to 26V; and over the full input common-mode range (0V to V
+
can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output
(Note 5) V
(Note 9)
R
I
R
I
V
V
R
V
V
V
IN(+)
IN(+)
+
+
+
+
O
S
S
L
= 26V
= +15V (V
≥ 2 kΩ
= 26V
= 5V, R
= 0Ω
= 0Ω
= 2V
− I
or I
(Continued)
IN(−)
IN(−)
+
L
, V
= 15V, T
A
= 10 kΩ
O
≤ +85˚C.
+
CM
Swing = 1V to 11V)
. At values of supply voltage in excess of +15V, continuous short-circuits can exceed the power
Conditions
= 0V
A
= 25˚C
4
R
V
V
V
V
V
V
IN
IN
+
IN
IN
+
L
+
−
−
+
= 10 kΩ
= 15V
= 15V
= +1V,
= 0V,
= +1V,
= 0V,
+
voltage level (or to ground for a large overdrive) for the time duration
+
− 1.5V)
Min
15
23
10
0
5
LM2902
Typ
40
45
10
40
24
20
7
5
8
V
Max
200
500
100
+
60
10
−2
+
.
µV/˚C
pA/˚C
Units
V/mV
V
mA
mV
mV
mA
nA
nA
V