at88sc0808ca ATMEL Corporation, at88sc0808ca Datasheet
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
at88sc0808ca
Available stocks
Related parts for at88sc0808ca
at88sc0808ca Summary of contents
Page 1
... ESD Protection: 2,000V min Table 1-1. Pads Pad Description VCC Supply Voltage GND Ground SCL/CLK Serial Clock Input SDA/IO Serial Data Input/Output RST Reset Input ISO Module “SOIC, PDIP” CryptoMemory AT88SC0808CA Summary TSSOP 5204BS–CRYPT–2/09 ...
Page 2
... Up to four unique key sets may be used for these operations. The AT88SC0808CA offers the ability to communicate with virtually any smart card reader using the asynchronous protocol (Gem- plus Patent) defined in ISO 7816-3 ...
Page 3
... Block Diagram VCC GND SCL/CLK SDA/IO RST 5. Connection Diagram Figure 5-1. Connection Diagram 2.7v - 5.5v Microprocessor 5204BS–CRYPT–2/09 Authentication, Power Encryption and Management Certification Unit Synchronous Data Transfer Interface Asynchronous Password Verification ISO Interface Reset Block Answer to Reset Random Generator EEPROM 2.7v - 3.6v CryptoMemory SDA SCL 3 ...
Page 4
... Upon activation of the reset sequence, the device outputs bytes contained in the 64- bit Answer-To-Reset register. An internal pull-up on the RST input pad allows the device to oper- ate in synchronous mode without bonding RST. The AT88SC0808CA does not support an Answer-To-Reset sequence in the synchronous mode of operation. ...
Page 5
Absolute Maximum Ratings Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated ...
Page 6
... Applicable over recommended operating range from V Symbol Parameter I SDA/IO Output High Current OH I SDA/IO Output Low Current OL Note prevent Latch Up Conditions from occurring during Power Up of the AT88SC0808CA, V applying V . For Powering Down Table 7-2. AC Characteristics Applicable over recommended operating range from V Parameter f Async Clock Frequency ...
Page 7
... Memory Reset After an interruption in communication due protocol errors, power loss or any reason, perform "Acknowledge Polling" to properly recover from the condition. Acknowledge polling consists of sending a start condition followed by a valid CryptoMemory command byte and determining if the device responded with an ACKNOWLEDGE. Figure 8-1. Bus Time for 2-Wire Serial Communications. SCL: Serial Clock, SDA: Serial Data I/O 5204BS– ...
Page 8
... Write Cycle Timing. SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn Note: Figure 8-3. Data Validity Figure 8-4. START and STOP Definitions AT88SC0808CA 8 ACK t WR STOP CONDITION The Write Cycle time twr is the time from a valid stop condition of a write sequence to the end of the internal clear/write cycle. DATA ...
Page 9
Figure 8-5. Output Acknowledge 5204BS–CRYPT–2/09 9 ...
Page 10
... If the same security requirements are selected for multiple zones, then these zones may effectively be accessed as one larger zone. Figure 9-1. User Zone ZONE $0 $00 - User 0 - $78 User 1 $ User 6 $78 $00 - User 7 - $78 AT88SC0808CA 128 Bytes 128 Bytes $ 5204BS–CRYPT–2/09 $7 ...
Page 11
... The configuration memory consists of 2048 bits of EEPROM memory used for storage of pass- words, keys, codes, and also used for definition of security access rights for the user zones. Access rights to the configuration memory are defined in the control logic and are not alterable by the user after completion of personalization. ...
Page 12
... Non-volatile buffering of the data is done automatically by the device. During power-up in applications using Anti-Tearing, the host is required to perform ACK polling in the event that the device needs to carry out the data recovery process. AT88SC0808CA 12 (1) User Data ...
Page 13
Write Lock If a user zone is configured in the write lock mode, the lowest address byte of an 8-byte page constitutes a write access byte for the bytes of that page. For example, the write lock byte at ...
Page 14
... Cryptographic Message Authentication Codes AT88SC0808CA implements a data validity check function in the standard, authentication or encryption modes of operation. In the standard mode, data validity check is done through a Modification Detection Code (MDC), in which the host may read an MDC from the device in order to verify that the data sent was received correctly ...
Page 15
... For a user zones protected by this feature, data can only be programmed (bits change from a “1” “0”), but not erased (bits change from a “0” “1”). 14. Protocol Selection The AT88SC0808CA supports two different communication protocols. Smartcard Applications: Smartcard applications use ISO 7816-B protocol in asynchronous mode for compatibility and interoperability with industry standard smartcard readers ...
Page 16
... WRITE and READ commands, and then blowing fuses to lock this information in place. Gaining access to the configuration memory requires successful presentation of a secure (or transport) code. The initial signature of the secure (transport) code for the AT88SC0808CA AT88SC0808CA 16 ...
Page 17
... Initia lizing CryptoM emory for Smart Card Applications from th e product page at www.atmel.com/products/securemem. 16. Ordering Information Ordering Code Package AT88SC0808CA-MJ M2 – J Module AT88SC0808CA-MP M2 – P Module AT88SC0808CA-PU 8P3 AT88SC0808CA-SU 8S1 AT88SC0808CA-TU 8A2 AT88SC0808CA-WI 7 mil wafer (1) Package Type M2 – J Module M2 – P Module 8P3 8S1 8A2 Note: Formal drawings may be obtained from an Atmel sales office. ...
Page 18
... M2 module will yield 13.0 x 11.8 mm). Note: The module dimensions listed refer to the dimensions of the exposed metal contact area. The actual dimensions of the module after excise or punching from the carrier tape are generally 0.4 mm greater in both directions (i.e., a punched M2 module will yield 13.0 x 11.8 mm). AT88SC0808CA 18 ∅ ∅ 8.5 [mm] 8 ...
Page 19
Ordering Code: SU 18.1 8-lead SOIC TOP VIEW TOP VIEW e e SIDE VIEW SIDE VIEW Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. ...
Page 20
... E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 2325 Orchard Parkway San Jose, CA 95131 R AT88SC0808CA ...
Page 21
TSSOP 5204BS–CRYPT–2/09 21 ...
Page 22
... Revision History Table 20-1. Doc. Rev. 5204BS 5204AS AT88SC0808CA 22 Revision History Date Comments 2/2009 Connection Diagram inserted; DC Characteristics table updated. 7/2008 Initial document release. 5204BS–CRYPT–2/09 ...
Page 23
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2009 Atmel Corporation. All rights reserved. Atmel trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. International Atmel Asia ...