at27bv020 ATMEL Corporation, at27bv020 Datasheet
at27bv020
Available stocks
Related parts for at27bv020
at27bv020 Summary of contents
Page 1
... At V accessed in less than 90 ns. With a typical power dissipation of only MHz and V = 3V, the AT27BV020 consumes less than one fifth the power of a standard CC 5V EPROM. Standby mode supply current is typically less than 1 µA at 3V. The ...
Page 2
... Programming time is typically only 100 µs/byte. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry-standard programming equipment to select the proper programming algorithms and voltages. The AT27BV020 programs exactly the same way as a standard 5V AT27C020 and uses the same programming equipment. 2. Pin Configurations ...
Page 3
... Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the (1) operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect (1) device reliability. (1) AT27BV020 3 ...
Page 4
... Device Code byte Outputs OUT X V High High OUT V V High Identification Code CC ≤ 5.5V 6.5V. and A0 which is toggled H AT27BV020-90 -40°C - 85°C 2.7V to 3.6V 5V ± 10% 0902F–EPROM–12/07 ...
Page 5
... CC I (TTL 2 0.5V SB2 MHz mA OUT 2 -400 µ and removed simultaneously with or after expect during programming. The supply current would then be the sum AT27BV020 Min Max ±1 ± 100 = 3.6V 8 -0.6 0.8 -0 0 ...
Page 6
... Output float is defined as the point when data is no longer driven. AT27BV020 6 Condition ( after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27BV020-90 Min Max ACC 0902F–EPROM–12/07 ...
Page 7
... Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. 0902F–EPROM–12/ < (10 Note 100 pF including jig capacitance. Max 8 12 AT27BV020 Units Conditions OUT 7 ...
Page 8
... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27BV020 a 0.1 µF capacitor is required across V transients. 15. DC Programming Characteristics ± 5° 6.5 ± 0.25V Symbol Parameter ...
Page 9
... Atmel’s AT27BV020 Integrated Product Identification Code Codes A0 Manufacturer 0 Device Type 1 Note: 1. The AT27BV020 has the same Product Identification Code as the AT27C020. Both are programming compatible. 0902F–EPROM–12/07 = 13.0 ± 0.25V PP (1) Test Conditions Input Rise and Fall Times: (10 Input Pulse Levels: 0 ...
Page 10
... After the byte verifies properly, the next address is selected until all have been checked. V read again and compared with the original data to determine if the device passes or fails. AT27BV020 10 is raised to 13.0V. Each address is first programmed with one 100 µ then lowered to 5 ...
Page 11
... Plastic Thin Small Outline Package (TSOP) 32V 32-lead, Plastic Thin Small Outline Package (VSOP) 0902F–EPROM–12/07 Standby Ordering Code 0.02 AT27BV020-90JI AT27BV020-90TI AT27BV020-90VI Standby Ordering Code 0.02 AT27BV020-90JU AT27BV020-90TU Package Type AT27BV020 Package Operation Range 32J Industrial 32T (-40° 85° C) (1) 32V Package Operation Range 32J ...
Page 12
... Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27BV020 12 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER E1 E ...
Page 13
... Orchard Parkway San Jose, CA 95131 R 0902F–EPROM–12/07 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT27BV020 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – ...
Page 14
... This package conforms to JEDEC reference MO-142, Variation BA. 2. Dimensions D1 and E do not include mold protrusion. Allowable protrusion 0.15 mm per side and 0.25 mm per side. 3. Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT27BV020 14 PIN SEATING PLANE ...
Page 15
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2007 Atmel Corporation. All rights reserved. Atmel Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. International Atmel Asia ...