at27lv1026 ATMEL Corporation, at27lv1026 Datasheet
at27lv1026
Related parts for at27lv1026
at27lv1026 Summary of contents
Page 1
... Integrated Product Identification Code • Commercial and Industrial Temperature Ranges Description The AT27LV1026 is a high performance 16-bit interleaved low-voltage 1,048,576-bit one-time programmable read only memory (OTP EPROM) organized 32K x 16 bits. It requires only one supply in the range of 3.0V to 3.6V in normal read mode operation. ...
Page 2
... LA cycle will be terminated when CS is asserted high put- ting the device in standby mode, or another NLA cycle starts. The LA cycle can be resumed when CS is asserted low and ALE stays low. The AT27LV1026 will continuously output data within each LA cycle which is determined by the read RD signal. Continuous interleave read operation is possible as there is no physical limit to the linear access LA output ...
Page 3
... Note: (1) CS PGM CLK_EVEN Even Counter 15 32K x 16 Memory Array Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent dam- age to the device. This is a stress rating only and functional operation of the device at these or any ...
Page 4
... Identification Code 3.6V, or 4.5V V 5.5V 6.5V except A9 which is set to V and A0 which is toggled select the Device Code word. IH AT27LV1026 - - - 3.0V - 3.6V 3.0V - 3.6V 5V 10% Outputs D OUT D OUT High OUT High Z -55 5V ...
Page 5
DC and Operating Characteristics for Read Operation Symbol Parameter V = 3. Input Load Current LI I Output Leakage Current LO (2) ( Read/Standby Current PP1 PP ( Standby Current SB CC ...
Page 6
... Output float is defined as the point when data is no longer driven. 4. When reading a 27LV1026, a 0.1 F capacitor is required across V AT27LV1026 3.0V to 3.6V and 4.5V to 5.5V) CC (1) t LACYC t RDH t RDL t t ACCLA LA LA and ground to suppress spurious voltage transients. CC AT27LV1026 Condition Min Typ Max 70 80 ALE = 7.5 2 ALE = ALE = ...
Page 7
... PP RD ALE PGM CS Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must accompanied by the programmer. CS DFP 3. When programming the AT27LV1026 a 0.1 F capacitor is required across V transients. Note: (1) Max 10 12 (1) PROGRAM VIH ADDRESS STABLE VIL tAS tCS VIH ...
Page 8
... Input Low Level IL V Input High Level IH V Output Low Voltage OL V Output High Voltage Supply Current (Program and Verify) CC2 Supply Current PP2 Product Identification Voltage ID AT27LV1026 8 = 13.0 0.25V PP Limits Test Conditions Min Max -0.6 0 2.1 mA ...
Page 9
AC Programming Characteristics 6.5 0.25V Symbol Parameter t Address Setup Time Setup Time CSS t Data Setup Time DS t Address Hold Time AH t Data Hold Time ...
Page 10
... PGM pulse without verification. Then a verification / reprogramming loop is executed for each address. In the event a word fails to pass verification successive 50 s pulses are applied with a verification after each AT27LV1026 10 pulse. If the word fails to verify after 10 pulses have been is applied, the part is considered failed. After the word verifies ...
Page 11
... Plastic J-Leaded Chip Carrier (PLCC) 40V 40-Lead, Plastic Thin Small Outline Package (VSOP Ordering Code AT27LV1026-35JC AT27LV1026-35VC AT27LV1026-35JI AT27LV1026-35VI AT27LV1026-45JC AT27LV1026-45VC AT27LV1026-45JI AT27LV1026-45VI AT27LV1026-55JC AT27LV1026-55VC AT27LV1026-55JI AT27LV1026-55VI Package Type Package Operation Range 44J Commercial 40V ( 44J ...
Page 12
... TYP .500(12.7) REF SQ .022(.559) X 45° MAX (3X) AT27LV1026 12 40V, 40-Lead, Plastic Thin Small Outline Package (VSOP) Dimension in Millimeters and (Inches) JEDEC OUTLINE MO-142 CA .045(1.14) X 30° - 45° .012(.305) .008(.203) .630(16.0) SQ ...