psd4235g2 STMicroelectronics, psd4235g2 Datasheet - Page 49
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
psd4235g2
Manufacturer Part Number
psd4235g2
Description
Flash In-system Programmable Isp Peripherals For 16-bit Mcus 5v Supply
Manufacturer
STMicroelectronics
Datasheet
1.PSD4235G2.pdf
(129 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
psd4235g2-70U
Manufacturer:
ST
Quantity:
210
Company:
Part Number:
psd4235g2-70U
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
psd4235g2-90U
Manufacturer:
MURATA
Quantity:
34 000
Part Number:
psd4235g2-90U
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
psd4235g2-90UI
Manufacturer:
TI
Quantity:
8 802
Company:
Part Number:
psd4235g2V-90U
Manufacturer:
SHARP
Quantity:
201
PSD4235G2
11
11.1
11.2
11.3
Specific features
Flash Memory Sector Protect
Each sector of Primary or Secondary Flash memory can be separately protected against
Program and Erase cycles. Sector Protection provides additional data security because it
disables all Program or Erase cycles. This mode can be activated (or deactivated) through
the JTAG-ISP Port or a device programmer.
Sector protection can be selected for each sector using the PSDsoft Express program. This
automatically protects selected sectors when the device is programmed through the JTAG
Port or a device programmer. Flash memory sectors can be unprotected to allow updating of
their contents using the JTAG Port or a device programmer. The MCU can read (but cannot
change) the sector protection bits.
Any attempt to program or erase a protected Flash memory sector is ignored by the device.
The Verify operation results in a READ of the protected data. This allows a guarantee of the
retention of the Protection status.
The sector protection status can be read by the MCU through the Flash memory protection
and Secondary Flash memory protection registers (in the CSIOP block) or use the Read
Sector Protection instruction. See
Reset
The Reset instruction consists of one WRITE cycle (see
preceded by the standard two WRITE decoding cycles (writing AAh to AAAh, and 55h to
554h).
The Reset instruction must be executed after:
●
●
The Reset instruction immediately puts the Flash memory back into normal READ mode.
However, if there is an error condition (with the Error Flag bit (DQ5/DQ13) set to ’1’) the
Flash memory will return to the READ mode in 25 μs after the Reset instruction is issued.
The Reset instruction is ignored when it is issued during a Program or Bulk Erase cycle of
the Flash memory. The Reset instruction aborts any on-going Sector Erase cycle, and
returns the Flash memory to the normal READ mode in 25 μs.
Reset (RESET) pin
A pulse on the Reset (RESET) pin aborts any cycle that is in progress, and resets the Flash
memory to the READ mode. When the reset occurs during a Program or Erase cycle, the
Flash memory takes up to 25 μs to return to the READ mode. It is recommended that the
Reset (RESET) pulse (except for Power-on Reset, as described in
25μs so that the Flash memory is always ready for the MCU to fetch the bootstrap
instructions after the Reset cycle is complete.
Reading the Flash Protection Status or Flash ID
An Error condition has occurred (and the device has set the Error Flag bit (DQ5/DQ13)
to ’1’) during a Flash memory Program or Erase cycle.
Table 19
to
Table
20.
Table
29). It can also be optionally
Section
Specific features
22.1) be at least
49/129