ncp360 ON Semiconductor, ncp360 Datasheet - Page 4

• Manufacturer Part Number: ncp360
• Description: Usb Positive Ovp Pmosfet And Status Flag
• Manufacturer: ON Semiconductor

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. R
2. Human Body Model, 100 pF discharged through a 1.5 kW resistor following specification JESD22/A114.
3. Machine Model, 200 pF discharged through all pins following specification JESD22/A115.
4. Compliant with JEDEC Latch-up Test, up to maximum voltage range.
NOTE:
MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(Min/Max limits values (-40°C < T
FLAG Output Low Voltage
FLAG Leakage Current
EN Leakage Current
FLAG going up Delay
TIMINGS
Minimum Voltage (IN to GND)
Minimum Voltage (All others to GND)
Maximum Voltage (IN to GND)
Maximum Voltage (All others to GND)
Maximum Current from Vin to Vout (PMOS)
Thermal Resistance, Junction-to-Air (Note 1)
Operating Ambient Temperature Range
Storage Temperature Range
Junction Operating Temperature
ESD Withstand Voltage (IEC 61000-4-2)
Moisture Sensitivity
Input Voltage Range
Undervoltage Lockout Threshold
Uvervoltage Lockout Hysteresis
Overvoltage Lockout Threshold
Overvoltage Lockout Hysteresis
V
Supply Quiescent Current
OVLO Supply Current
Output Off State Current
EN Voltage High
EN Voltage Low
Start Up Delay
Output Turn Off Time
Alert Delay
Disable Time
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
Human Body Model (HBM), Model = 2 (Note 2)
Machine Model (MM) Model = B (Note 3)
in
qJA
versus V
is highly dependent on the PCB heat sink area (connected to PAD1, UDFN). See PCB Recommendations.
Thermal Shutdown parameter has been fully characterized and guaranteed by design.
Characteristic
out
Dopout
Rating
A
< +85°C) and V
UVLO
OVLO
FLAG
Symbol
Idd
EN
T
OVLO
UVLO
Vol
V
t
t
sdhyst
Idd
I
start
T
V
V
V
stop
t
t
t
drop
std
on
off
dis
sd
uvlo
leak
in
flag
ih
ol
hyst
leak
hyst
in
= +5.0 V. Typical values are T
From EN 0.4 to 1.2V to V
From V
From V
From V
From V
V
V
V
http://onsemi.com
in
in
in
V
increasing from 5 V to 8 V at 1 V/ms.
increasing from 5 V to 8 V at 3 V/ms
in
V
in
in
in
> OVLO, Sink 1 mA on FLAG pin
V
V
in
TSOP-5
in
> UVLO to V
> UVLO to FLAG = 1.2 V, See Fig 3
> OVLO to FLAG ≤ 0.4 V, See Fig 4
= 4.75 V. No output capacitor.
in
in
NCP360
> OVLO to V
V
V
V
falls down UVLO threshold
UDFN
No Load, V
rises up OVLO threshold
= 5 V, I charge = 500 mA
in
in
in
No output capacitor.
EN = 5.5 V or GND
= 5.25 V, EN = 1.2 V
FLAG level = 5 V
from 3.3 V to 5.25 V
from 3.3 V to 5.25 V
4
Conditions
V
in
= 7 V
out
in
out
out
= 5.25 V
= 0.8xV
≤ 0.3 V, See Fig 4
Symbol
Vmax
Vmin
≤ 0.3 V, See Fig 5
Vmax
A
Vmin
Imax
Vesd
R
MSL
T
T
T
qJA
= +25°C, unless otherwise noted.)
stg
A
J
in
in
in
, See Fig 3
15 Air, 8.0 Contact
-65 to +150
2.85
5.43
-40 to +85
Min
1.2
1.2
50
50
Level 1
Value
2000
-0.3
-0.3
600
305
260
150
200
7.0
21
5.675
Typ
100
105
170
150
3.0
5.0
4.0
3.0
0.8
1.0
2.0
70
24
50
26
30
Max
3.15
125
200
400
5.9
0.4
1.5
2.0
20
90
35
85
37
15
°C/W
Unit
mA
kV
°C
°C
°C
V
V
V
V
V
V
-
Unit
mV
mV
mV
mV
ms
mA
mA
mA
nA
nA
ms
ms
ms
ms
°C
°C
V
V
V
V
V