tmp88ps38ng TOSHIBA Semiconductor CORPORATION, tmp88ps38ng Datasheet
tmp88ps38ng
Related parts for tmp88ps38ng
tmp88ps38ng Summary of contents
Page 1
... For a discussion of how the reliability of microcontrollers can be predicted, please refer to Section 1.3 of the chapter entitled Quality and Reliability Assurance/Handling Precautions. Purchase of TOSHIBA I these components Specification as defined by Philips. CMOS 8-Bit Microcontroller TMP88PS38NG/FG OTP RAM 64 Kbytes (256 bytes) P-SDIP42-600-1.78 2 Kbytes 24 Kbytes P-QFP44-1414-0 ...
Page 2
... Pin Assignments Package P-SDIP42-600-1.78 TMP88PS38NG Package P-QFP44-1414-0.80K TMP88PS38F P-SDIP42-600-1.78 VSS ( ) P40 PWM P41 PWM P42 PWM P43 PWM P44 PWM P45 PWM P46 PWM P47 PWM 7 (TC2 P50 INT 0 PWM 8 (SI1/SCL1/ ) P51 PWM 9 (SO1/SDA1) P52 ( / /INT2/TC1/AIN0) P53 KWU 0 SCK 1 ( /AIN1) P54 ...
Page 3
Operational Description The configuration and function of the TMP88PS38 are the same as those of the TMP88CS38, except in that a one-time PROM is used instead of an on-chip mask ROM. 1. Operation Mode The TMP88PS38 has two mode: MCU ...
Page 4
Data Memory The TMP88PS38 has an on-chip 2-Kbyte data memory (Static RAM). 00000H 04000H Program storage area 13EFFH 20000H OSD font area 25FFFH FFF00H Vector table storage area FFFFFH TMP88CS38 MCU mode 00000H 04000H Program storage area 0FEFFH 20000H ...
Page 5
... PGM P61 P47 P67 P64 D7 P57 to P40 P50 N.C. XIN (Open, only TMP88PS38FG) P71 P20 P31 P34 XOUT VSS RESET VVSS OVSS BM11174A for TMP88PS38NG BM11175A for TMP88PS38FG 88PS38-5 TMP88PS38 For more in formation on pins refer to the section on pin function. 2005-05-18 ...
Page 6
... P71, P20, P31, P34 RESET XIN Input XOUT Output N.C. Open PROM programmer connection adaptor socket: BM11174A for TMP88PS38NG Function PROM address inputs PROM data inputs/outputs Chip enable signal input (Active low) Output enable signal input (Active low) Program mode signal input +12.75 V/5 V (Program supply voltage) +6 ...
Page 7
Programming Flowchart (High-speed Programming Mode) The high-speed programming mode is achieved by applying the program voltage (+12. the VPP pin when Vcc = 6.25 V. After the address and input data are stable, the data is programmed ...
Page 8
Writing Method for General-purpose PROM Program (1) Adapters BM11174A: TMP88PS38N BM11175A: TMP88PS38F (2) PROM programmer specifying i) PROM type is specified to TC571000D. (Note 1) Writing voltage: 12.75 V (High-speed programming mode) ii) Data transfer (copy) (Note 1) In ...
Page 9
Input/Output Circuit (1) Control pins The input/output circuitries of the TMP88PS38 control pins are shown below. Control Pin I/O Osc.enable XIN I/O XOUT Address-trap-reset I/O RESET Watchdog-timer-reset System-clock-reset / STOP INT 5 Input (P20) P20/ STOP TEST Input Input/Output Circuitry ...
Page 10
Input/output ports Port I/O Initial “High-Z” P20 I/O P30 Initial “High-Z” to P33 P50, I/O P57 Disable P70, P71 Open-drain P34, output enable P35, I/O P51, P52 Initial “High-Z” P40 to I/O Disable P47 Initial “High-Z” P53 Disable to ...
Page 11
Port I/O Initial “High-Z” Disable P60, I/O P61 Initial “High-Z” P62 (at I/O CSOUT) Disable Initial “High-Z” P62, I/O P63 Disable Initial “High-Z” P64 to I/O Disable P67 Input/Output Circuitry VDD Key-on wakeup VDD R ...
Page 12
Electrical Characteristics Absolute Maximum Ratings Parameter Supply voltage Programmable voltage Input voltage Output voltage Output current (Per 1 pin) Output current (Total) Power dissipation [Topr = 70°C] Soldering temperature (Time) Storage temperature Operating temperature Note: The absolute maximum ratings are ...
Page 13
DC Characteristics Parameter Symbol Hysteresis voltage V Hysteresis inputs HS I TEST IN1 I Open-drain ports IN2 Input current I Tri-state ports IN3 I RESET IN4 Input resistance R RESET IN2 I Sink open-drain ports LO1 Output leakage current I ...
Page 14
AC Characteristics Parameter Symbol Machine cycle time t cy High level clock pulse width T WCH Low level clock pulse width T WCL Recommended oscillating conditions Parameter Oscillator High-frequency Ceramic resonator oscillation Note 1: To keep reliable operation, shield the ...
Page 15
DC/AC Characteristics (PROM mode) (1) Read operation (V = 5.0 ± 0.25 V, Topr = 25 ± 5°C) DD Parameter Input high voltage (A0 to A16 PGM Input low voltage (A0 to A16 ...
Page 16
High-speed Programming Timing A16 Unknown PGM V PP Note 1: When Vcc power supply is turned on or after, Vpp must be increased. When Vcc power supply is turned off or before, Vpp ...
Page 17
Package P-SDIP42-600-1.78 88PS38-17 TMP88PS38 Unit: mm 2005-05-18 ...
Page 18
P-QFP44-1414-0.80K 88PS38-18 TMP88PS38 Unit: mm 2005-05-18 ...
Page 19
TMP88PS38 2005-05-18 ...