lpc2142 NXP Semiconductors, lpc2142 Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
lpc2142
Manufacturer Part Number
lpc2142
Description
Single-chip 16-bit/32-bit Microcontrollers; Up To 512 Kb Flash With Isp/iap, Usb 2.0 Full-speed Device, 10-bit Adc And Dac
Manufacturer
NXP Semiconductors
Datasheet
1.LPC2142.pdf
(39 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
lpc2142FBD
Manufacturer:
IR
Quantity:
20 000
Company:
Part Number:
lpc2142FBD64
Manufacturer:
NXP
Quantity:
491
Company:
Part Number:
lpc2142FBD64
Manufacturer:
NXP/31
Quantity:
5 250
Part Number:
lpc2142FBD64
Manufacturer:
ST
Quantity:
20 000
Part Number:
lpc2142FBD64+151
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
lpc2142FBD64,151
Manufacturer:
NXP Semiconductors
Quantity:
10 000
NXP Semiconductors
LPC2141_42_44_46_48_3
Product data sheet
6.11.1 Features
6.12.1 Features
6.11 UARTs
6.12 I
The LPC2141/42/44/46/48 each contain two UARTs. In addition to standard transmit and
receive data lines, the LPC2144/46/48 UART1 also provides a full modem control
handshake interface.
Compared to previous LPC2000 microcontrollers, UARTs in LPC2141/42/44/46/48
introduce a fractional baud rate generator for both UARTs, enabling these microcontrollers
to achieve standard baud rates such as 115200 with any crystal frequency above 2 MHz.
In addition, auto-CTS/RTS flow-control functions are fully implemented in hardware
(UART1 in LPC2144/46/48 only).
The LPC2141/42/44/46/48 each contain two I
The I
(SCL), and a serial data line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver or a transmitter with the
capability to both receive and send information (such as memory)). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I
controlled by more than one bus master connected to it.
The I
(Fast I
2
•
•
•
•
•
•
•
•
•
•
•
•
•
C-bus serial I/O controller
16 B Receive and Transmit FIFOs
Register locations conform to 16C550 industry standard
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values
Transmission FIFO control enables implementation of software (XON/XOFF) flow
control on both UARTs
LPC2144/46/48 UART1 equipped with standard modem interface signals, this module
also provides full support for hardware flow control (auto-CTS/RTS)
Compliant with standard I
Easy to configure as master, slave, or master/slave
Programmable clocks allow versatile rate control
Bidirectional data transfer between masters and slaves
Multi-master bus (no central master)
Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus
Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus
2
2
C-bus is bidirectional, for inter-IC control using only two wires: a serial clock line
C-bus implemented in LPC2141/42/44/46/48 supports bit rates up to 400 kbit/s
2
C-bus).
Rev. 03 — 19 October 2007
2
C-bus interface
LPC2141/42/44/46/48
2
Single-chip 16-bit/32-bit microcontrollers
C-bus controllers.
2
C-bus is a multi-master bus, it can be
© NXP B.V. 2007. All rights reserved.
17 of 39