wm8941 Wolfson Microelectronics plc, wm8941 Datasheet - Page 18
![no-image](/images/no-image-200.jpg)
wm8941
Manufacturer Part Number
wm8941
Description
Mono Codec With Speaker Driver And Video Buffer
Manufacturer
Wolfson Microelectronics plc
Datasheet
1.WM8941.pdf
(94 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
wm8941G
Manufacturer:
MITSUMI
Quantity:
971
Part Number:
wm8941GEFL
Manufacturer:
WOLFSON
Quantity:
20 000
WM8941
w
INPUT SIGNAL PATH
MICROPHONE INPUTS
The WM8941 can accommodate a variety of microphone configurations including single ended and
differential inputs. The inputs through the MICN, MICP and optionally AUX pins are amplified through
the input PGA as shown in Figure 6 .
A pseudo differential input is the preferential configuration where the positive terminal of the input
PGA is connected to the MICP input pin by setting MICP2INPPGA=1. The microphone ground should
then be connected to MICN (when MICN2INPPGA=1) or optionally to AUX (when AUX2INPPGA=1)
input pins.
Alternatively a single ended microphone can be connected to the MICN input with MICN2INPPGA set
to 1. The non-inverting terminal of the input PGA should be connected internally to VMID by setting
MICP2INPPGA to 0.
In pseudo-differential mode the larger signal should be input to MICP and the smaller (e.g. noisy
ground connections) should be input to MICN.
AUDIO INTERFACES
The WM8941 has a standard audio interface, to support the transmission of audio data to and from
the chip. This interface is a 4 wire standard audio interface which supports a number of audio data
formats including I
operate in master or slave modes.
CONTROL INTERFACES
To allow full software control over all its features, the WM8941 supports 2 or 3 wire control interface.
It is fully compatible and an ideal partner for a wide range of industry standard microprocessors,
controllers and DSPs. The selection between 2-wire mode and 3-wire mode is determined by the
state of the MODE / GPIO pin. If MODE / GPIO is high then 3-wire control mode is selected, if
MODE is low then 2-wire control mode is selected.
In 2 wire mode, only slave operation is supported, and the address of the device is fixed as 0011010.
CLOCKING SCHEMES
WM8941 offers the normal audio DAC clocking scheme operation, where 256fs MCLK is provided to
the DAC/ADC.
However, a PLL is also included which may be used to generate the internal master clock frequency
in the event that this is not available from the system controller. This PLL uses an input clock,
typically the 12MHz USB or ilink clock, to generate high quality audio clocks. If this PLL is not
required for generation of these clocks, it can be reconfigured to generate alternative clocks which
may then be output on the GPIO pin and used elsewhere in the system.
POWER CONTROL
The design of the WM8941 has given much attention to power consumption without compromising
performance. It operates at low supply voltages, and includes the facility to power off any unused
parts of the circuitry under software control.
As a power saving measure, ADC or DAC logic in the DSP core is held in its last enabled state when
the ADC or DAC is disabled. In order to prevent pops and clicks on restart due to residual data in the
filters, the master clock must remain for at least 64 input samples after the ADC or DAC has been
disabled.
The WM8941 has 3 flexible analogue inputs: two microphone inputs, and an auxiliary input. These
inputs can be used in a variety of ways. The input signal path before the ADC has a flexible PGA
block which then feeds into a gain boost/mixer stage.
2
S, DSP Mode, MSB-First, left justified and MSB-First, right justified, and can
PD, Rev 4.0, August 2008
Production Data
18