s5u1c33000c Epson Electronics America, Inc., s5u1c33000c Datasheet - Page 479

• Manufacturer Part Number: s5u1c33000c
• Description: Cmos 32-bit Single Chip Microcomputer S5u1c33000c Manual
• Manufacturer: Epson Electronics America, Inc.

S5U1C33000C MANUAL
(C COMPILER PACKAGE FOR S1C33 FAMILY) (Ver. 4)
Cannot load debug information,
please check SRF33 file.
Cannot load debug information,
too many lines.
Cannot open com port.
Cannot open file any more.
Cannot open file.
Cannot open parallel port.
Cannot open parameter file.
Cannot open stdio file.
Cannot read chip name.
Cannot read emulation memory map.
Cannot read FO area size.
Cannot read IROM size.
Cannot read MCU/MPU information.
Cannot read parameter file version.
Cannot read PRC board status.
Cannot read PRC board version.
Cannot read stdin file.
Cannot regist address any more.
Cannot set address any more.
Cannot set alias anymore.
Cannot set enable address anymore.
Cannot set hardware PC break.
Cannot set software PC break.
Cannot set temporary break.
Cannot write flash memory.
Cannot write log file.
Cannot write stdout file.
Cannot write trace file.
Chip name should be 5 characters.
Chip name should be start with "33".
Command is not supported at present mode.
Communication data size error.
Communication error.
CPU down.
CPU is not running.
CPU is running.
Current mode is not source mode.
Data alignment error.
Data incomplete.
Data mask range (0-0xFFFF).
Data mask range (0-0xFFFFFFFF).
Data range (0-0xFF).
Data range (0-0xFFFF).
Data range (0-0xFFFFFFFF).
Debug data failure.
Diagnostic test failure.
Duplicate input address.
Duplicate input break number.
Empty file.
Erase routine is not set.
File end during guidance input.
File not found.
Flash memory error.
Flash memory is not mapped.
Flash ROM is protected.
Fo address range (0-0x3FFF).
Format error.
Function not found.
ICE is busy.
ICE is free run mode.
ICE is maintenance mode.
ICE is not mapped.
ICE system error.
Error message
The debug information load has failed; the srf33 format is illegal.
(Program/ data is load successfully.)
The debug information load has failed; too many source lines are
included. (Program/ data is loaded successfully.)
The COM port or baud rate cannot be set.
The number of files exceeds the limit.
The file cannot be opened.
The parallel port cannot be opened.
The parameter file cannot be opened.
The stdio file cannot be opened.
Chip name information (.par file) cannot be read.
Emulation memory map information (.par file) cannot be read.
FOPT size information (.par file) cannot be read.
Internal ROM size information (.par file) cannot be read.
MCU/MPU mode information (.par file) cannot be read.
Parameter file version information (.par file) cannot be read.
S5U1C33xxxP board status information (.par file) cannot be read.
S5U1C33xxxP board version information (.par file) cannot be read.
The stdin file cannot be read.
8 hardware PC break points have been registered.
16 software PC break points have been set.
100 aliases have been registered.
2 hardware PC break points have been enabled.
The hardware PC break point cannot be set.
The software PC break point cannot be set.
Temporary break point cannot be set.
Data cannot be written to the flash memory.
Log data cannot be written to the file.
The output data cannot be written to the stdout file.
Trace data cannot be written to the file.
The chip name length is not 5 characters.
The chip name must begin with 33.
A command not supported for the current mode is executed.
The communication data size is incorrect.
Overrun, framing, or BCC error has occurred during transmission
from/to the S5U1C33104H.
The S5U1C33xxxP board operates erratically.
The S5U1C33104H CPU has stopped operating.
The S5U1C33104H CPU is executing.
String search is only available in the source display mode.
Alignment in the srf file is incorrect.
The file structure is illegal.
The data mask is out of the range.
The data mask is out of the range.
The input data is out of the range.
The input data is out of the range.
The input data is out of the range.
The debugging data is illegal.
The S5U1C33104H self-diagnosis resulted in error.
Same break address is set twice.
Same break point number is set twice.
The file does not contain data.
A flash memory erase routine has not been defined.
The command file has ended in the middle of the parameters of the
guidance format.
The file cannot be found.
Error in writing or erasing flash memory.
The S5U1C33104H flash memory is not mapped.
Flash memory is protected against access.
The option dump address is out of the range.
The format is illegal.
The function cannot be found.
The S5U1C33104H is busy processing a job.
The S5U1C33104H is operating in free-run mode.
The S5U1C33104H is placed in maintenance mode.
The S5U1C33104H built-in memory is not mapped.
S5U1C33104H system error has occurred.
EPSON
Content
CHAPTER 16: DEBUGGER
463