mt88ebnr Zarlink Semiconductor, mt88ebnr Datasheet - Page 11

• Manufacturer Part Number: mt88ebnr
• Description: 4-wire Calling Number Identification Circuit 2 4-wire Cnic2 Semiconductor Inc
• Manufacturer: Zarlink Semiconductor

In Figure 55, t
responding. The total delay from the start of CAS to STD responding is t
CAS to STD responding is t
FSK Demodulation
The FSK characteristics are shown in Table 4. In North America, TIA (Telecommunications Industry Association)
also sets standards. The Type 1 Caller ID CPE standard is ANSI/TIA/EIA-716. The Type 2 standard is TIA/EIA-777.
The North American FSK characteristics in Table 4 are from ANSI/TIA/EIA-716. They differ from those Bellcore
published in SR-TSV-002476 and SR-3004. Bellcore is represented in TR41.3.1 and will synchronize to the TIA
requirements in its future documents.
The TIA Type 1 standard includes an FSK reject level:
•
•
The MT88E45B is compliant with the Bellcore/TIA, ETSI and BT requirements with the Tip/Ring op-amp gains in
Table 4. In Europe if the country specific FSK requirements do not incorporate ETSI’s FSK reject level then the
Tip/Ring op-amp gain can also be 0 dB at 5 V and -3.5 dB at 3 V to meet the ETSI minimum CAS level for on-hook
signalling (-40 dBV).
Mark (Logical 1) Frequency
Space (Logical 0) Frequency
Received Signal Level
Signal Reject Level
Transmission Rate
Twist (V
Signal to Noise Ratio
Tip/Ring Op-Amp (GS1) Gain
Vdd = 5V +/- 10%
Tip/Ring Op-Amp (GS1) Gain
Vdd = 3V +/- 10%
a. ANSI/TIA/EIA-716 and TIA/EIA-777. Bellcore has agreed to the values and will synchronize its requirements.
b. ETS 300 778-1 (On-hook) Sep 97, ETS 300 778-2 (Off-hook) Jan 98.
c. SIN 227 Issue 3 Nov 97, SIN242 Issue 2 Nov 96.
d. North American on-hook signalling range. The off-hook range is inside the on-hook range: 190mVrms to 12mVrms.
e. dBm - Decibels above or below a reference power of 1 mW into 600 ohms. 0 dBm = 0.7746 Vrms
f. dBV - Decibels above or below a reference voltage of 1 Vrms. 0 dBV = 1 Vrms.
g. ETSI on-hook signalling range. The off-Hook signalling levels are inside this range: -8.78 to -30.78 dBm (-11 to -33 dBV).
h. The 5V ETSI Tip/Ring op-amp gain can be 0 dB if there is no FSK reject level requirement.
i. The 3V ETSI Tip/Ring op-amp gain can be -3.5dB if there is no FSK reject level requirement.
if data is not preceded by ringing (e.g., VMWI), FSK signals below 3mVrms (-48.24 dBm) shall be rejected
if data is preceded by ringing, FSK detection may be extended below 3mVrms
MARK
Parameter
DP
/V
SPACE
is the delay from the start of CAS to EST responding, t
)
ABS
=t
DA
+t
On-hook No Ring Signalling
North America: Bellcore
GA
-48.24 dBm (3mVrms) for
+25 dB (200<f<3200Hz)
Table 4 - FSK Signal Characteristics
-12 dB (60<f<=120Hz)
-6 dB (120<f<=200Hz)
.
-4.23 to -36.20 dBm
(476 to 12 mVrms)
+6 dB (f>=3200Hz)
1200 baud +/- 1%
-18 dB (f<=60Hz)
1200 Hz +/- 1%
2200 Hz +/- 1%
Single Tone (f):
such as VMWI
-6 to +10 dB
-3.5 dB
Zarlink Semiconductor Inc.
0 dB
MT88E45
11
d
a
-5.78 to -33.78 dBm
(-8 to -36 dBV)
(300 to 3400 Hz)
Europe: ETSI
On-hook only:
DA
-47.78 dBm
REC
(-50dBV)
>= 25 dB
-5.5 dB
-2 dB
is the delay from the end of CAS to EST
=t
DP
+t
h
1200 baud +/- 1%
2100 Hz +/- 1.5%
1300 Hz +/- 1.5%
i
GP.
f,g
b
The total delay from the end of
-6 to +6 dB
e
-5.78 to -37.78 dBm
(300 to 3400 Hz)
(-8 to -40 dBV)
>= 20 dB
UK: BT
-3.5 dB
0 dB
Data Sheet
c