92hdw74c Integrated Device Technology, 92hdw74c Datasheet - Page 37

• Manufacturer Part Number: 92hdw74c
• Description: 6-channel Hd Audio Codec, Single Or Dual Spdif
• Manufacturer: Integrated Device Technology

SIX CHANNEL HD AUDIO CODEC, PREMIUM WLP 3/4 COMPLIANT
D2
D3
Differential Power
Voltage Reference Outputs
Phased Locked Loop
ESD / Latchup
92HDW74C1
SIX CHANNEL HD AUDIO CODEC, PREMIUM WLP 3/4 COMPLIANT
10
10
One Stereo ADC Didd
One Stereo ADC Aidd
One Stereo DAC Didd
One Stereo DAC Aidd
VREFOut
VREFILT (VAG)
PLL lock time
PLL (or HD Audio Bit CLK) 24MHz clock
jitter
Latch-up
ESD - Human Body Model
Charged Device Model
1.
presence of signal and outlined in AES6id, measured “A weighted” over 20 Hz to 20 kHz bandwidth
2.Ratio of Full Scale signal to idle channel noise output is measured “A weighted” over a 20 Hz to a 20 kHz bandwidth.
(AES17-1991 Idle Channel Noise or EIAJ CP-307 Signal-to-noise Ratio).
3.THD+N ratio as defined in AES17 and outlined in AES6id,non-weighted, over 20 Hz to 20 kHz bandwidth.Results at the jack
are dependent on external components and will likely be 1 - 2dB worse.
4.Peak-to-Peak Ripple over Passband meets ± 0.125dB limits, 48 kHz or 44.1 kHz Sample Frequency. 1dB limit.
5.Stop Band rejection determines filter requirements. Out-of-Band rejection determines audible noise.
6.The integrated Out-of-Band noise generated by the DAC process, during normal PCM audio playback, over a bandwidth 28.8
to 100 kHz, with respect to a 1 Vrms DAC output.
7.Gain drift is the change in analog volume control gain for each step across the supported 0
referenced to the 25
8.± 1dB limits for Line Output & 0 dB gain, at -20dBV
9.Spurious tone rejection is tested with ADC dither enabled and compared to ADC performance without dither.
10.Can be set to 0.5 or 0.8 AVdd.
Dynamic Range is the ratio of the full scale signal to the noise output with a -60dBFS signal as defined in AES17 as SNR in the
10
Parameter
D1 Aidd
D2 Didd
D2 Aidd
D3 Didd
D3 Aidd
10
o
Table 16. 92HDW74C1 5V, 4.75V, and 3.3V Analog Performance Characteristics
C gain value and specified in ppm per
Per converter power consumption
As described in JESD78A Class II
All converters, ports and mixer off
As described in JESD22-A114-B
As described in JESD22-C101
5.0V, 4.75V, & 3.3V
5.0V, 4.75V, & 3.3V
5.0V, 4.75V, & 3.3V
5.0V, 4.75V, & 3.3V
5.0V, 4.75V, & 3.3V
Anti-pop enabled
Conditions
o
3.3V
3.3V
3.3V
3.3V
C
37
AVdd
All
All
All
All
All
All
All
92HDW74C1
Min
500
o
2K
C TO 70
-
0.45 X
0.5 X
AVdd
AVdd
Typ
150
1K
35
14
28
14
10
96
70
3K
11
3
3
4
o
C temperature range
Max
200
500
-
PC AUDIO
V 1.0 03/08
degC
Unit
usec
psec
mA
mA
mA
mA
mA
mA
mA
mA
mA
V
V
V
V