am49lv6408m Meet Spansion Inc., am49lv6408m Datasheet - Page 27
![no-image](/images/no-image-200.jpg)
am49lv6408m
Manufacturer Part Number
am49lv6408m
Description
Stacked Multi-chip Mcp 64 Mbit 4 M ? 16 Bit Flash Memory And 8 Mbit 512k ? 16 Bit Pseudo Static Ram
Manufacturer
Meet Spansion Inc.
Datasheet
1.AM49LV6408M.pdf
(63 pages)
COMMAND DEFINITIONS
Writing specific address and data commands or se-
quences into the command register initiates device op-
erations. Tables
command sequences. Writing incorrect address and
data values or writing them in the improper sequence
may place the device in an unknown state. A reset
command is then required to return the device to read-
ing array data.
All addresses are latched on the falling edge of WE#
or CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens
November 5, 2003
Addresses
(x16)
4Ch
4Dh
40h
41h
42h
43h
44h
45h
46h
47h
48h
49h
4Ah
4Bh
4Eh
4Fh
50h
11
0002h/
00B5h
00C5h
0050h
0052h
0049h
0031h
0033h
0008h
0002h
0001h
0001h
0004h
0000h
0000h
0001h
0003h
0001h
Data
and
12
define the valid register
Table 10. Primary Vendor-Specific Extended Query
Query-unique ASCII string “PRI”
Major version number, ASCII
Minor version number, ASCII
Address Sensitive Unlock (Bits 1-0)
0 = Required, 1 = Not Required
Process Technology (Bits 7-2) 0010b = 0.23 µm MirrorBit
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
Sector Protect
0 = Not Supported, X = Number of sectors in per group
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
Sector Protect/Unprotect scheme
04 = 29LV800 mode
Simultaneous Operation
00 = Not Supported, X = Number of Sectors in Bank
Burst Mode Type
00 = Not Supported, 01 = Supported
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
ACC (Acceleration) Supply Minimum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
ACC (Acceleration) Supply Maximum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
Top/Bottom Boot Sector Flag
00h = Uniform Device without WP# protect, 02h = Bottom Boot Device, 03h = Top Boot Device,
04h = Uniform sectors bottom WP# protect, 05h = Uniform sectors top WP# protect
Program Suspend
00h = Not Supported, 01h = Supported
A D V A N C E
Am49LV6408M
I N F O R M A T I O N
first. Refer to the
diagrams.
Reading Array Data
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is ready to read array data
after completing an Embedded Program or Embedded
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the erase-suspend-read mode, after
w h i c h t h e s y s t e m c a n r e a d d a t a f r o m a n y
Description
AC Characteristics
section for timing
25