mt9htf12872pz Micron Semiconductor Products, mt9htf12872pz Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
mt9htf12872pz
Manufacturer Part Number
mt9htf12872pz
Description
1gb X72, Ecc, Sr 240-pin Ddr2 Sdram Rdimm
Manufacturer
Micron Semiconductor Products
Datasheet
1.MT9HTF12872PZ.pdf
(14 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
mt9htf12872pz-80EH1
Manufacturer:
AVAGO
Quantity:
3 323
Table 5:
PDF: 09005aef83c641c6/Source: 09005aef83c6415f
HTF9C128x72pz.fm - Rev. A 11/09 EN
RAS#, CAS#, WE#
DQS#[17:9]
DQS[17:9],
CK0, CK0#
DQS#[8:0]
V
DQS[8:0],
DQ[63:0]
Symbol
DM[8:0]/
Err_Out
EVENT#
BA[2:0]
A[15:0]
RESET#
SA[2:0]
CB[7:0]
V
DD
Par_In
ODT0
CKE0
SDA
V
DDSPD
S0#
SCL
V
/V
REF
SS
DDQ
Pin Descriptions
(open drain)
(open drain)
Output
Output
Supply
Supply
Supply
Supply
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Input
Type
I/O
I/O
I/O
I/O
Description
Address inputs: Provide the row address for ACTIVE commands, and the column
address and auto precharge bit (A10) for READ/WRITE commands, to select one location
out of the memory array in the respective bank. A10 sampled during a PRECHARGE
command determines whether the PRECHARGE applies to one device bank (A10 LOW,
device bank selected by BA[2:0]) or all device banks (A10 HIGH). A[13:0] (1GB). A[15:14]
are connected for parity.
Bank address inputs: BA[2:0] define the device bank to which an ACTIVE, READ,
WRITE, or PRECHARGE command is being applied. BA[2:0] define which mode register
(MR, EMR1, EMR2, and EMR3) is loaded during the LOAD MODE command.
Clock: CK and CK# are differential clock inputs. All control, command, and address input
signals are sampled on the crossing of the positive edge of CK and the negative edge of
CK#. Output data (DQ, DQS, and DQS#) is referenced to the crossings of CK and CK#.
Clock enable: CKE enables (registered HIGH) and disables (registered LOW) internal
circuitry and clocks on the DDR2 SDRAM.
Input data mask: DM is an input mask signal for write data. Input data is masked when
DM is sampled HIGH, along with the input data, during a write access. DM is sampled on
both edges of DQS. Although the DM pins are input-only, DM loading is designed to
match that of the DQ and DQS pins. If RDQS is disabled, DQS[17:9] become DM[8:0] and
DQS#[17:9] are no function.
On-die termination: ODT enables (registered HIGH) and disables (registered LOW)
termination resistance internal to the DDR2 SDRAM. When enabled in normal operation,
ODT is only applied to the following pins: DQ, DQS, DQS#, DM, and CB. The ODT input
will be ignored if disabled via the LOAD MODE command.
Parity input: Parity bit for the address, RAS#, CAS#, and WE#.
Command inputs: RAS#, CAS#, and WE# (along with S#) define the command being
entered.
Reset: Asynchronously forces all registered outputs LOW when RESET# is LOW. This
signal can be used during power-up to ensure that CKE is LOW and DQ are High-Z.
Chip select: S# enables (registered LOW) and disables (registered HIGH) the command
decoder.
Serial address inputs: These pins are used to configure the SPD EEPROM address range
on the I
Serial clock for SPD EEPROM: SCL is used to synchronize communication to and from
the SPD EEPROM.
Check bits.
Data input/output: Bidirectional data bus.
Data strobe: DQS# is only used when differential data strobe mode is enabled via the
LOAD MODE command. Output with read data. Edge-aligned with read data. Input with
write data. Center-aligned with write data.
Serial data: SDA is a bidirectional pin used to transfer addresses and data into and out
of the SPD EEPROM on the module on the I
Parity error output: Parity error found on the command and address bus.
Temperature event: The EVENT# pin is asserted by the temperature sensor when critical
temperature thresholds have been exceeded.
Power supply: 1.8V ±0.1V. The component V
V
SPD EEPROM power supply: +1.7V to +3.6V.
Reference voltage: V
Ground.
DD
.
2
C bus.
1GB (x72, ECC, SR) 240-Pin DDR2 SDRAM RDIMM
DD
/2.
4
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Pin Assignments and Descriptions
2
C bus.
DD
and V
DDQ
are connected to the module
©2009 Micron Technology, Inc. All rights reserved.