m366s3253cts Samsung Semiconductor, Inc., m366s3253cts Datasheet
m366s3253cts
Related parts for m366s3253cts
m366s3253cts Summary of contents
Page 1
... GENERAL DESCRIPTION The Samsung M366S3253CTS is a 32M bit x 64 Synchronous Dynamic RAM high density memory module. The Samsung M366S3253CTS consists of eight CMOS 32M x 8 bit with 4banks Synchronous DRAMs in TSOP-II 400mil package and a EEPROM in 8-pin TSSOP package on a 168-pin glass-epoxy sub- strate ...
Page 2
... M366S3253CTS PIN CONFIGURATION DESCRIPTION Pin Name CLK System clock CS Chip select CKE Clock enable A0 ~ A12 Address BA0 ~ BA1 Bank select address RAS Row address strobe CAS Column address strobe WE Write enable DQM0 ~ 7 Data input/output mask DQ0 ~ 63 Data input/output V /V Power supply/ground ...
Page 3
... M366S3253CTS FUNCTIONAL BLOCK DIAGRAM CS0 DQM0 DQM CS DQ0 DQ0 DQ1 DQ1 DQ2 DQ2 U0 DQ3 DQ3 DQ4 DQ4 DQ5 DQ5 DQ6 DQ6 DQ7 DQ7 DQM1 DQM CS DQ8 DQ0 DQ9 DQ1 DQ10 DQ2 U1 DQ11 DQ3 DQ12 DQ4 DQ13 DQ5 DQ14 DQ6 DQ15 DQ7 ...
Page 4
... M366S3253CTS ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin relative to Vss Voltage on V supply relative to Vss DD Storage temperature Power dissipation Short circuit current Note : Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. ...
Page 5
... M366S3253CTS DC CHARACTERISTICS (Recommended operating condition unless otherwise noted, T Parameter Symbol Operating current I CC1 (One bank active Precharge standby cur- CC2 rent in power-down mode I PS CC2 I N CC2 Precharge standby cur- rent in non power-down mode I NS CC2 I P Active standby current in ...
Page 6
... M366S3253CTS AC OPERATING TEST CONDITIONS Parameter AC input levels (Vih/Vil) Input timing measurement reference level Input rise and fall time Output timing measurement reference level Output load condition Output 870 (Fig output load circuit OPERATING AC PARAMETER (AC operating conditions unless otherwise noted) Parameter ...
Page 7
... M366S3253CTS AC CHARACTERISTICS (AC operating conditions unless otherwise noted) REFER TO THE INDIVIDUAL COMPONENET, NOT THE WHOLE MODULE. Parameter CAS latency=3 CLK cycle time CAS latency=2 CAS latency=3 CLK to valid output delay CAS latency=2 CAS latency=3 Output data hold time CAS latency=2 CLK high pulse width ...
Page 8
... M366S3253CTS SIMPLIFIED TRUTH TABLE Command Register Mode register set Auto refresh Entry Refresh Self refresh Bank active & row addr. Read & Auto precharge disable column address Auto precharge enable Write & Auto precharge disable column address Auto precharge enable Burst stop ...
Page 9
... M366S3253CTS PACKAGE DIMENSIONS 0.118 (3.000) 0.125 0.375 (3.175) (9.525) 0.096 (2.44) .118DIA 0.004 (3.000DIA 0.100) 0.350 (8.890) .450 (11.430) 0.250 (6.350) 0.123 (3.125 0.079 0.004 (2.000 0.100) Detail A Tolerances : .005(.13) unless otherwise specified The used device is 32Mx8 SDRAM, TSOP SDRAM Part No. : K4S560832C 5 ...
Page 10
... M366S3253CTS M366S3253CTS-L7C/L7A/L1H/L1L, C7C/C7A/C1H/C1L • Organization : 32MX64 • Composition : 32MX8 *8 • Used component part # : K4S560832C-TL7C/7A/1H/1L,TC7C/7A/1H/1L • rows in module : 1row • banks in component : 4 banks • Feature : 1,375 mil height & single sided component • Refresh : 8K/64ms • Contents : Byte#. Function described bytes written into serial memory at module manufacturer ...
Page 11
... M366S3253CTS SERIAL PRESENCE DETECT INFORMATION Byte # Function described 35 Data signal input hold time 36~61 Superset information (maybe used in future) 62 SPD data revision code 63 Checksum for bytes Manufacturer JEDEC ID code 65~71 ...... Manufacturer JEDEC ID code 72 Manufacturing location 73 Manufacturer part # (Memory module) 74 Manufacturer part # (DIMM configuration) ...