CM2596SCN263 CHAMP [Champion Microelectronic Corp.], CM2596SCN263 Datasheet
![no-image](/images/no-image-200.jpg)
CM2596SCN263
Related parts for CM2596SCN263
CM2596SCN263 Summary of contents
Page 1
... Requires only 4 external components Thermal shutdown and current limit protection Requires only 4 external components Excellent line and load regulation specifications TTL shutdown capability Package Type TO-263 CM2596SSCN263 CM2596SZJCN263 CM2596SCN263 CM2596SGSCN263 CM2596SGZJCN263 CM2596SGCN263 CM2596S Output Voltage C: Adjustable SC: 3.3V ZJC: 5V Champion Microelectronic Corporation ...
Page 2
PIN CONFIGURATION TO-220 Top View ABSOLUTE MAXIMUM RATINGS Input Voltage (V ) …….………………………………………….……. +45V POWER ENABLE Pin Input Voltage ….…………………………………. –0.3V ≦V≦25V Storage Temperature ………………………………….….…... -65℃ to +150℃ Lead Temperature (10 sec.) ……..……………………..….…………….... 260℃ Operating ...
Page 3
ELECTRICAL CHARACTERISTICS Electrical Characteristics 0mA, and T OUT Unless otherwise specified, Vin=12V for 3.3V,5V,adjustable version. I Parameter Device Output Voltage CM2596SS (Note 1) CM2596SZJ Output Voltage CM2596SS (Note 1) CM2596SZJ CM2596SS Output Voltage (Note 1) CM2596SZJ Feedback ...
Page 4
Note 1: External components such as the catch diode, inductor, input and output capacitors can affect switching regulator system performance. Refer to Application Information for details. Note 2: The oscillator frequency reduces to approximately 11KHz in the event of fault ...
Page 5
APPLICATION CIRCUIT 2006/11/27 Rev 1 TEP Figure1. Fixed Output Voltage Figure2. Adjustable Output Voltage Champion Microelectronic Corporation CM2596S OWN OLTAGE Vout = Vref ( Vout ...
Page 6
TYPICAL CHARACTERISTICS 2006/11/27 Rev 1 TEP Champion Microelectronic Corporation CM2596S OWN OLTAGE EGULATOR Page 6 ...
Page 7
Rev 1 TEP Champion Microelectronic Corporation CM2596S OWN OLTAGE EGULATOR V =32V IN Page 7 ...
Page 8
APPLICATION INFORMATION External component selector Input Capacitors (Cin required that VIN must be bypassed with at least a 100uF electrolytic capacitor for stability. Also strongly recommended the capacitor’s leads must be short, wide and located near ...
Page 9
Output Voltage Ripple and Transients The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor. The output ripple voltage of a switching power supply will contain a sawtooth ripple ...
Page 10
Feedback Connection For fixed output voltage version, the FB (feedback) pin must be connected to V place the output voltage ratio resistors near CM2596S as possible in order to minimize the noise introduction. Enable It is required that the ENABLE ...
Page 11
PACKAGE DIMENSION 2006/11/27 Rev 1 TEP TO-220 (N220) Symbol F(Φ TO-220B (N220B) Champion Microelectronic Corporation CM2596S OWN OLTAGE EGULATOR Min(mm) Max(mm) 14.22 16.51 9.66 ...
Page 12
Rev 1 TEP TO-263 (N263) TO-263 (N263) Lead Position Overlay Champion Microelectronic Corporation CM2596S OWN OLTAGE Symbol Min(mm) Max(mm) A. 9.88 10.67 B 8.20 9.17 C 4.34 4. 1.40 E 0.31 0.53 ...
Page 13
Champion Microelectronic Corporation (CMC) reserves the right to make changes to its products or to discontinue any integrated circuit product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing ...