BT136-500F TECCOR [Teccor Electronics], BT136-500F Datasheet - Page 133
![no-image](/images/no-image-200.jpg)
BT136-500F
Manufacturer Part Number
BT136-500F
Description
Thyristor Product Catalog
Manufacturer
TECCOR [Teccor Electronics]
Datasheet
1.BT136-500F.pdf
(223 pages)
- Current page: 133 of 223
- Download datasheet (3Mb)
AN10039
Introduction
Due to high-volume production techniques, thyristors are now
priced so that almost any electrical product can benefit from elec-
tronic control. A look at the fundamentals of SCR and triac phase
controls shows how this is possible.
Output Power Characteristics
Phase control is the most common form of thyristor power con-
trol. The thyristor is held in the off condition — that is, all current
flow in the circuit is blocked by the thyristor except a minute leak-
age current. Then the thyristor is triggered into an “on” condition
by the control circuitry.
For full-wave AC control, a single triac or two SCRs connected in
inverse parallel may be used. One of two methods may be used
for full-wave DC control — a bridge rectifier formed by two SCRs
or an SCR placed in series with a diode bridge as shown in
Figure AN1003.1.
Figure AN1003.1
Figure AN1003.2 illustrates voltage waveform and shows com-
mon terms used to describe thyristor operation. Delay angle is
the time during which the thyristor blocks the line voltage. The
conduction angle is the time during which the thyristor is on.
©2002 Teccor Electronics
Thyristor Product Catalog
Line
Line
Control
Circuit
Two SCR AC Control
One SCR DC Control
Control
Circuit
SCR/Triac Connections for Various Methods of
Phase Control
Load
Load
Line
Line
Two SCR DC Control
Triac AC Control
Load
Control
Circuit
Control
Circuit
Load
AN1003 - 1
Phase Control Using Thyristors
It is important to note that the circuit current is determined by the
load and power source. For simplification, assume the load is
resistive; that is, both the voltage and current waveforms are
identical.
Figure AN1003.2
Different loads respond to different characteristics of the AC
waveform. For example, some are sensitive to average voltage,
some to RMS voltage, and others to peak voltage. Various volt-
age characteristics are plotted against conduction angle for
half- and full-wave phase control circuits in Figure AN1003.3
and Figure AN1003.4.
Delay (Triggering) Angle
Sine Wave Showing Principles of Phase Control
Voltage Applied to Load
Conduction Angle
Full-wave Rectified Operation
AN1003
http://www.teccor.com
+1 972-580-7777
Related parts for BT136-500F
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![SM16JZ41](/images/manufacturer_photos/0/6/655/teccor_electronics_tmb.jpg)
Part Number:
Description:
Cross Reference Data to Teccor Part Numbers (See datasheet appendix)
Manufacturer:
Teccor Electronics
Datasheet:
![IP103](/images/manufacturer_photos/0/6/655/teccor_electronics_tmb.jpg)
Part Number:
Description:
Cross Reference Data to Teccor Part Numbers (See datasheet appendix)
Manufacturer:
Teccor Electronics
Datasheet:
![IP105](/images/manufacturer_photos/0/6/655/teccor_electronics_tmb.jpg)
Part Number:
Description:
Cross Reference Data to Teccor Part Numbers (See datasheet appendix)
Manufacturer:
Teccor Electronics
Datasheet:
![P0080SD](/images/manufacturer_photos/0/6/655/teccor_electronics_tmb.jpg)
Part Number:
Description:
Manufacturer:
Teccor Electronics
Datasheet:
![P3100AD](/images/manufacturer_photos/0/6/655/teccor_electronics_tmb.jpg)
Part Number:
Description:
solid state crowbar devices
Manufacturer:
Teccor Electronics
Datasheet:
![S6S1](/images/manufacturer_photos/0/6/655/teccor_electronics_tmb.jpg)
Part Number:
Description:
Sensitive SCRs (0.8 A to 10 A) S6S1Sensitive SCRs
Manufacturer:
Teccor Electronics
Datasheet: