ra07m4047msa Quanzhou Jinmei Electronic Co.,Ltd., ra07m4047msa Datasheet - Page 7

• Manufacturer Part Number: ra07m4047msa
• Description: Mitsubishi Rf Mosfet Module
• Manufacturer: Quanzhou Jinmei Electronic Co.,Ltd.

PRECAUTIONS, RECOMMENDATIONS, and APPLICATION INFORMATION:
Construction:
ESD:
Mounting:
Soldering and Defluxing:
Thermal Design of the Heat Sink:
RA07M4047MSA
This module consists of an alumina substrate soldered onto a copper flange. For mechanical protection, a plastic
cap is attached with silicone. The MOSFET transistor chips are die bonded onto metal, wire bonded to the
substrate, and coated with resin. Lines on the substrate (eventually inductors), chip capacitors, and resistors form
the bias and matching circuits. Wire leads soldered onto the alumina substrate provide the DC and RF connection.
Following conditions must be avoided:
a) Bending forces on the alumina substrate (for example, by driving screws or from fast thermal changes)
b) Mechanical stress on the wire leads (for example, by first soldering then driving screws or by thermal expansion)
c) Defluxing solvents reacting with the resin coating on the MOSFET chips (for example, Trichlorethylene)
d) Frequent on/off switching that causes thermal expansion of the resin
e) ESD, surge, overvoltage in combination with load VSWR, and oscillation
This MOSFET module is sensitive to ESD voltages down to 1000V. Appropriate ESD precautions are required.
Heat sink flatness must be less than 50 µm (a heat sink that is not flat or particles between module and heat sink
may cause the ceramic substrate in the module to crack by bending forces, either immediately when driving screws
or later when thermal expansion forces are added).
A thermal compound between module and heat sink is recommended for low thermal contact resistance and to
reduce the bending stress on the ceramic substrate caused by the temperature difference to the heat sink.
The module must first be screwed to the heat sink, then the leads can be soldered to the printed circuit board.
M3 screws are recommended with a tightening torque of 0.4 to 0.6 Nm.
This module is designed for manual soldering.
The lead (terminal) must be soldered after the module is screwed onto the heat sink.
The temperature of the lead (terminal) soldering should be lower than 350°C and shorter than 3 second.
Ethyl Alcohol is recommend for removing flux. Trichloroethylene solvents must not be used (they may cause
bubbles in the coating of the transistor chips which can lift off the bond wires).
At P
The channel temperatures of each stage transistor T
When mounting the module with the thermal resistance of 2.84 °C/W, the channel temperature of each stage
transistor is:
The 175°C maximum rating for the channel temperature ensures application under derated conditions.
out
T
T
For long-term reliability, it is best to keep the module case temperature (T
temperature T
P
R
T
T
ch1
ch2
ch1
ch2
=7.0W, V
out
th(case-air)
Stage
2
1
+ P
= T
= T
= T
= T
nd
st
in
case
case
air
air
) of the heat sink, including the contact resistance, is:
= (90°C - 60°C) / (7.0W/40% – 7.0W + 0.05W) = 2.84 °C/W
+ 46.3 °C
+ 66.2 °C
DD
+ (7.2V x 0.69A – 2.0W + 0.05W) x 5.4°C/W
+ (7.2V x 2.43A – 7.0W + 2.0W) x 2.9°C/W
=7.2V and P
0.05
(W)
2.0
P
air
in
=60°C and P
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
P
(W)
2.0
7.0
in
out
=50mW each stage transistor operating conditions are:
out
=7.0W, the required thermal resistance R
R
(°C/W)
th(ch-case)
5.4
2.9
MITSUBISHI ELECTRIC
I
DD
ch
7/8
= T
@ η
0.69
2.43
(A)
case
T
=40%
RoHS COMPLIANCE
+ (V
= T
= T
DD
case
case
V
x I
(V)
7.2
DD
+ 16.3 °C
+ 36.2 °C
DD
- P
out
th (case-air)
case
+ P
RA07M4047MSA
) below 90°C. For an ambient
in
) x R
MITSUBISHI RF POWER MODULE
= ( T
th(ch-case)
case
- T
air
are:
) / ( (P
out
5 Feb 2008
/ η
T
) -