LTC2413 LINER [Linear Technology], LTC2413 Datasheet - Page 21

• Manufacturer Part Number: LTC2413
• Description: 24-Bit No Latency ADC, with Simultaneous 50Hz/60Hz Rejection
• Manufacturer: LINER [Linear Technology]

APPLICATIO S I FOR ATIO
A similar situation may occur during the sleep state when
CS is pulsed HIGH-LOW-HIGH in order to test the conver-
sion status. If the device is in the sleep state (EOC = 0), SCK
will go LOW. Once CS goes HIGH (within the time period
defined above as t
For a heavy capacitive load on the SCK pin, the internal
pull-up may not be adequate to return SCK to a HIGH level
before CS goes low again. This is not a concern under
normal conditions where CS remains LOW after detecting
EOC = 0. This situation is easily overcome by adding an
external 10k pull-up resistor to the SCK pin.
Internal Serial Clock, 2-Wire I/O,
Continuous Conversion
This timing mode uses a 2-wire, all output (SCK and SDO)
interface. The conversion result is shifted out of the device
by an internally generated serial clock (SCK) signal, see
Figure 11. CS may be permanently tied to ground, simpli-
fying the user interface or isolation barrier.
The internal serial clock mode is selected at the end of the
power-on reset (POR) cycle. The POR cycle is concluded
approximately 0.5ms after V
(INTERNAL)
SDO
SCK
CS
CONVERSION
EOCtest
U
), the internal pull-up is activated.
U
BIT 31
EOC
CC
exceeds 2.2V. An internal
Figure 11. Internal Serial Clock, CS = 0 Continuous Operation
SLEEP
BIT 30
W
ANALOG INPUT RANGE
–0.5V
BIT 29
SIG
REF
1, 7, 8, 9, 10, 15, 16
0.1V TO V
REFERENCE
U
TO 0.5V
VOLTAGE
BIT 28
MSB
1 F
2.7V TO 5.5V
REF
CC
2
3
4
5
6
BIT 27
V
REF
REF
IN
IN
GND
CC
+
–
LTC2413
weak pull-up is active during the POR cycle; therefore, the
internal serial clock timing mode is automatically selected
if SCK is not externally driven LOW (if SCK is loaded such
that the internal pull-up cannot pull the pin HIGH, the
external SCK mode will be selected).
During the conversion, the SCK and the serial data output
pin (SDO) are HIGH (EOC = 1). Once the conversion is
complete, SCK and SDO go LOW (EOC = 0) indicating the
conversion has finished and the device has entered the
low power sleep state. The part remains in the sleep state
a minimum amount of time (1/2 the internal SCK period)
then immediately begins outputting data. The data output
cycle begins on the first rising edge of SCK and ends after
the 32nd rising edge. Data is shifted out the SDO pin on
each falling edge of SCK. The internally generated serial
clock is output to the SCK pin. This signal may be used
to shift the conversion result into external circuitry. EOC
can be latched on the first rising edge of SCK and the last
bit of the conversion result can be latched on the 32nd
rising edge of SCK. After the 32nd rising edge, SDO goes
HIGH (EOC = 1) indicating a new conversion is in progress.
SCK remains HIGH during the conversion.
+
–
DATA OUTPUT
BIT 26
SDO
SCK
CS
F
O
14
13
12
11
2-WIRE I/O
= EXTERNAL OSCILLATOR
= INTERNAL OSC/SIMULTANEOUS 50Hz/60Hz REJECTION
LSB
BIT 5
24
BIT 0
LTC2413
CONVERSION
sn2413 2413fs
21
2413 F11