LTC3407A LINER [Linear Technology], LTC3407A Datasheet - Page 7

• Manufacturer Part Number: LTC3407A
• Description: Dual Synchronous 600mA, 1.5MHz Step-Down DC/DC Regulator
• Manufacturer: LINER [Linear Technology]

OPERATION
The LTC3407A uses a constant frequency, current mode
architecture. The operating frequency is set at 1.5MHz
and can be synchronized to an external oscillator. Both
channels share the same clock and run in-phase. To suit
a variety of applications, the selectable MODE/SYNC pin
allows the user to trade-off noise for effi ciency.
The output voltage is set by an external divider returned
to the V
output voltage with a reference voltage of 0.6V and adjusts
the peak inductor current accordingly. Overvoltage and
undervoltage comparators will pull the POR output low if
the output voltage is not within ±8.5%. The POR output
will go high after 65,536 clock cycles (about 44ms in pulse
skipping mode) of achieving regulation.
Main Control Loop
During normal operation, the top power switch (P-channel
MOSFET) is turned on at the beginning of a clock cycle when
the V
into the inductor and the load increases until the current
limit is reached. The switch turns off and energy stored in
the inductor fl ows through the bottom switch (N-channel
MOSFET) into the load until the next clock cycle.
The peak inductor current is controlled by the internally
compensated I
ror amplifi er.This amplifi er compares the V
0.6V reference. When the load current increases, the
V
decrease causes the error amplifi er to increase the I
voltage until the average inductor current matches the
new load current.
The main control loop is shut down by pulling the RUN/SS
pin to ground.
Low Current Operation
Two modes are available to control the operation of the
LTC3407A at low currents. Both modes automatically
switch from continuous operation to the selected mode
when the load current is low.
To optimize effi ciency, the Burst Mode operation can be
selected. When the load is relatively light, the LTC3407A
automatically switches into Burst Mode operation in which
FB
voltage decreases slightly below the reference. This
FB
voltage is below the reference voltage. The current
FB
pins. An error amplifi er compares the divided
TH
voltage, which is the output of the er-
FB
pin to the
TH
the PMOS switch operates intermittently based on load
demand with a fi xed peak inductor current. By running
cycles periodically, the switching losses which are domi-
nated by the gate charge losses of the power MOSFETs
are minimized. The main control loop is interrupted when
the output voltage reaches the desired regulated value. A
voltage comparator trips when I
off the switch and reducing the power. The output capaci-
tor and the inductor supply the power to the load until I
exceeds 0.65V, turning on the switch and the main control
loop which starts another cycle.
For lower ripple noise at low currents, the pulse skipping
mode can be used. In this mode, the LTC3407A continues
to switch at a constant frequency down to very low cur-
rents, where it will begin skipping pulses.
Dropout Operation
When the input supply voltage decreases toward the
output voltage, the duty cycle increases to 100% which
is the dropout condition. In dropout, the PMOS switch is
turned on continuously with the output voltage being equal
to the input voltage minus the voltage drops across the
internal P-channel MOSFET and the inductor.
An important design consideration is that the R
of the P-channel switch increases with decreasing input
supply voltage (See Typical Performance Characteristics).
Therefore, the user should calculate the power dissipation
when the LTC3407A is used at 100% duty cycle with low
input voltage (See Thermal Considerations in the Applica-
tions Information Section).
Low Supply Operation
The LTC3407A incorporates an undervoltage lockout circuit
which shuts down the part when the input voltage drops
below about 1.65V to prevent unstable operation.
A general LTC3407A application circuit is shown in
Figure 1. External component selection is driven by the
load requirement, and begins with the selection of the
inductor L. Once the inductor is chosen, C
can be selected.
TH
is below 0.65V, shutting
LTC3407A
IN
and C
DS(ON)
3407afa
7
OUT
TH