LTC3616 LINER [Linear Technology], LTC3616 Datasheet - Page 16
![no-image](/images/no-image-200.jpg)
LTC3616
Manufacturer Part Number
LTC3616
Description
6A, 4MHz Monolithic Synchronous Step-Down DC/DC Converter
Manufacturer
LINER [Linear Technology]
Datasheet
1.LTC3616.pdf
(28 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC3616EUDD
Manufacturer:
LT
Quantity:
10 000
Company:
Part Number:
LTC3616EUDD#PBF
Manufacturer:
LT
Quantity:
5 000
Part Number:
LTC3616HUDD#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC3616IUDD
Manufacturer:
LT
Quantity:
10 000
LTC3616
APPLICATIONS INFORMATION
Output Capacitor (C
The selection of C
ESR to minimize voltage ripple and load step transients
(low ESR ceramic capacitors are discussed in the next
section). Typically, once the ESR requirement is satisfied,
the capacitance is adequate for filtering. The output ripple
ΔV
where f
tance and ΔI
ripple is highest at maximum input voltage since ΔI
increases with input voltage.
In surface mount applications, multiple capacitors may
have to be paralleled to meet the capacitance, ESR or RMS
current handling requirement of the application. Aluminum
electrolytic, special polymer, ceramic and dry tantalum
capacitors are all available in surface mount packages.
Tantalum capacitors have the highest capacitance density,
but can have higher ESR and must be surge tested for
use in switching power supplies. Aluminum electrolytic
capacitors have significantly higher ESR, but can often
be used in extremely cost-sensitive applications provided
that consideration is given to ripple current ratings and
long-term reliability.
Ceramic Input and Output Capacitors
Ceramic capacitors have the lowest ESR and can be cost
effective, but also have the lowest capacitance density,
high voltage and temperature coefficients, and exhibit
audible piezoelectric effects. In addition, the high Q of
ceramic capacitors along with trace inductance can lead
to significant ringing.
They are attractive for switching regulator use because
of their very low ESR, but great care must be taken when
using only ceramic input and output capacitors.
16
OUT
ΔV
OUT
is determined by:
OSC
≤ ΔI
= operating frequency, C
L
= ripple current in the inductor. The output
L
• ESR +
⎛
⎝ ⎜
OUT
OUT
is typically driven by the required
) Selection
8 • f
SW
1
• C
OUT
OUT
⎞
⎠ ⎟
= output capaci-
L
Ceramic capacitors are prone to temperature effects
which require the designer to check loop stability over
the operating temperature range. To minimize their large
temperature and voltage coefficients, only X5R or X7R
ceramic capacitors should be used.
When a ceramic capacitor is used at the input and the power
is being supplied through long wires, such as from a wall
adapter, a load step at the output can induce ringing at the
V
be mistaken as loop instability. At worst, the ringing at the
input can be large enough to damage the part.
Since the ESR of a ceramic capacitor is so low, the input
and output capacitor must instead fulfill a charge storage
requirement. During a load step, the output capacitor
must instantaneously supply the current to support the
load until the feedback loop raises the switch current
enough to support the load. The time required for the
feedback loop to respond is dependent on the compensa-
tion components and the output capacitor size. Typically,
3 to 4 cycles are required to respond to a load step, but
only in the first cycle does the output drop linearly. The
output droop, V
linear drop of the first cycle; however, this behavior can
vary depending on the compensation component values.
Thus, a good place to start is with the output capacitor
size of approximately:
This is only an approximation; more capacitance may
be needed depending on the duty cycle and load step
requirements.
In most applications, the input capacitor is merely required
to supply high frequency bypassing, since the impedance
to the supply is very low.
IN
C
pin. At best, this ringing can couple to the output and
OUT
≈
f
SW
3.5 • ΔI
• V
DROOP
DROOP
OUT
, is usually about 2 to 4 times the
3616f