LTC3789 LINER [Linear Technology], LTC3789 Datasheet - Page 8

• Manufacturer Part Number: LTC3789
• Description: High Voltage High Current Controller for Battery Charging and Power Management
• Manufacturer: LINER [Linear Technology]

pin FuncTions
LTC4000
VM (Pin 1/Pin 25): Voltage Monitor Input. High impedance
input to an accurate comparator with a 1.193V threshold
(typical). This pin controls the state of the RST output
pin. Connect a resistor divider (R
monitored voltage and GND, with the center tap point con-
nected to this pin. The falling threshold of the monitored
voltage is calculated as follows:
where R
and GND. Tie to the BIAS pin if voltage monitoring func-
tion is not used.
RST (Pin 2/Pin 26): High Voltage Open Drain Reset Output.
When the voltage at the VM pin is below 1.193V, this status
pin is pulled low. When driven low, this pin can disable a
DC/DC converter when connected to the converter’s en-
able pin. This pin can also drive an LED to provide a visual
status indicator of a monitored voltage. Short this pin to
GND when not used.
IIMON (Pin 3/Pin 27): Input Current Monitor. The voltage
on this pin is 20 times (typical) the sense voltage (V
across the input current sense resistor(R
providing a voltage proportional to the input current.
Connect an appropriate capacitor to this pin to obtain a
voltage representation of the time-average input current.
Short this pin to GND to disable input current limit feature.
IL (Pin 4/Pin 28): Input Current Limit Programming. Con-
nect the input current programming resistor (R
pin. This pin sources 50µA of current. The regulation loop
compares the voltage on this pin with the input current
monitor voltage (V
ingly to ensure that the programmed input current limit is
not exceeded. The input current limit is determined using
the following formula:
where R
the CLN pins. Leave the pin open for the maximum input
current limit of 50mV/R
8
I
V
ILIM
VM _ RST
= 2.5µA •
VM2
IS
is the sense resistor connected to the IN and
is the bottom resistor between the VM pin
=
R
VM1
⎛
⎜
⎝
IIMON
R
R
R
IL
IS
VM2
+ R
⎞
⎟
⎠
IS
), and drives the ITH pin accord-
VM2
.
(QFN/SSOP)
• 1.193V
VM1
, R
VM2
) between the
IS
), therefore
IL
) to this
IN,CLN
)
ENC (Pin 5/Pin 1): Enable Charging Pin. High impedance
digital input pin. Pull this pin above 1.5V to enable charg-
ing and below 0.5V to disable charging. Leaving this pin
open causes the internal 1µA pull-up current to pull the
pin to 2.5V (typical).
IBMON (Pin 6/Pin 2): Battery Charge Current Monitor. The
voltage on this pin is 20 times (typical) the sense voltage
(V
therefore providing a voltage proportional to the battery
charge current. Connect an appropriate capacitor to this
pin to obtain a voltage representation of the time-average
battery charge current. Short this pin to GND to disable
charge current limit feature.
CX (Pin 7/Pin 3): Charge Current Termination Pro-
gramming. Connect the charge current termination pro-
gramming resistor (R
impedance input to a comparator and sources 5μA of
current. When the voltage on this pin is greater than the
charge current monitor voltage (V
turns high impedance indicating that the CX threshold is
reached. When this occurs, the charge current is imme-
diately terminated if the TMR pin is shorted to the BIAS
pin, otherwise charging continues until the charge termi-
nation timer expires. The charge current termination value
is determined using the following formula:
Where R
and the CSN pins. Note that if R
R
charge current termination value is one tenth the full charge
current, more familiarly known as C/10. Short this pin to
GND to disable CX termination.
CL
CSP ,CSN
I
C / X
is the charge current programming resistor, then the
=
CS
) across the battery current sense resistor (R
(
0.25µA • R
is the sense resistor connected to the CSP
R
CS
CX
CX
) to this pin. This pin is a high
)
− 0.5mV
CX
= R
IBMON
CL
≤ 19.1kΩ, where
), the CHRG pin
CS
4000f
),