AD712AH Analog Devices, AD712AH Datasheet
AD712AH
Available stocks
Related parts for AD712AH
AD712AH Summary of contents
Page 1
... Extended reliability PLUS screening is available, specified over the commercial and industrial temperature ranges. PLUS REV. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use ...
Page 2
AD712–SPECIFICATIONS AD712J/A/S Parameter Min 1 INPUT OFFSET VOLTAGE Initial Offset MIN MAX vs. Temp vs. Supply 76/76/76 MIN MAX Long-Term Offset Stability 2 INPUT BIAS CURRENT ...
Page 3
... C/Watt; JC 8-Lead SOIC Package: = 100 For supply voltages less than 18 V, the absolute maximum input voltage is equal to the supply voltage. REV Model 18 V AD712ACHIPS AD712AH and – AD712AQ AD712BH AD712BQ AD712CH AD712CN AD712JN AD712JR AD712JR-REEL AD712JR-REEL7 AD712KN ...
Page 4
AD712 –Typical Performance Characteristics SUPPLY VOLTAGE Volts Figure 1. Input Voltage Swing vs. Supply Voltage ...
Page 5
GAIN PHASE 100pF LOAD 0 0 –20 –20 10 100 1k 10k 100k 1M 10M FREQUENCY – Hz Figure 10. Open-Loop Gain and Phase Margin vs. Frequency 100 80 ...
Page 6
AD712 –60 –40 – TEMPERATURE – C Figure 19. Slew Rate vs. Temperature +V S 0.1 F 1/2 AD712 0.1 F SQUARE WAVE –V S INPUT Figure 22a. ...
Page 7
OPTIMIZING SETTLING TIME Most bipolar high-speed D/A converters have current outputs; therefore, for most applications, an external op amp is required for current-to-voltage conversion. The settling time of the con- verter/op amp combination depends on the settling time of the ...
Page 8
AD712 OP AMP SETTLING TIME - A MATHEMATICAL MODEL The design of the AD712 gives careful attention to optimizing individual circuit components; in addition, a careful trade-off was made: the gain bandwidth product (4 MHz) and slew rate (20 V/ ...
Page 9
The photos of Figures 28a and 28b show the dynamic response of the AD712 in the settling test circuit of Figure 29. 5V 100 5mV Figure 28a. Settling Characteristics +10 V Step Upper Trace: ...
Page 10
AD712 D/A CONVERTER APPLICATIONS The AD712 is an excellent output amplifier for CMOS DACs. It can be used to perform both 2 quadrant and 4 quadrant op- eration. The output impedance of a DAC using an inverted R-2R ladder approaches ...
Page 11
Figures 33a and 33b show the settling time characteristics of the AD712 when used as a DAC output buffer for the AD7545. 100 Full-Scale Positive Transition 100 Full-Scale Negative Transition Figure 33. ...
Page 12
AD712 PD711 BUFF 100 500mV –10V ADC IN a. Source Current = 2 mA PD711 BUFF 100 500mV –5V ADC IN b. Sink Current = 1 mA Figure 35. ADC Input Unity Gain Buffer ...
Page 13
SECOND ORDER LOW PASS FILTER Figure 38 depicts the AD712 configured as a second order Butterworth low pass filter. With the values as shown, the corner frequency will be 20 kHz; however, the wide bandwidth of the AD712 permits a ...
Page 14
AD712 +15V 0 0.001 F A1 AD711 0.1 F –15V 100k 9-POLE CHEBYCHEV FILTER Figure 40 shows the AD712 and its dual counterpart, the AD711 9-pole Chebychev filter using active frequency dependent negative resistors (FDNR). ...
Page 15
Mini-DIP (N-8) 0.390 (9.91 0.250 0.310 (6.35) (7.87 PIN 1 0.035 0.01 (0.890 0.25) 0.165 0.01 4.19 0.25 0.18 0.01 0.125 (3.18) (4.57 0.76) MIN SEATING 0.033 (0.84) 0.018 0.003 0.100 PLANE (2.54) NOM (0.460 0.081) ...