UPC8100 NEC, UPC8100 Datasheet
UPC8100
Available stocks
Related parts for UPC8100
UPC8100 Summary of contents
Page 1
... Remark To order evaluation samples, please contact your local NEC sales office. (Order number: PC8100GR) The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. P10817EJ3V0DS00 (3rd edition) ...
Page 2
... INTERNAL BLOCK DIAGRAM AND PIN CONNECTIONS REG. REG GND 2. RF BYPASS 3. RF INPUT 4. PEAKING OUT 5. P/S (for DOWN CONV.) 6. P/S (for UP CONV (for UP CONV OUTPUT 9. GND 10. MIX OUTPUT1 11. MIX OUTPUT2 12. GND 13. ...
Page 3
... CC intactor 9 GND 0.0 FUNCTION AND APPLICATION (V) – Ground for downconverter. Must be connected to the system ground with minimum inductance. Ground pat- tern on the board should be formed as wide as possible. (Track length should be kept as short as possible.) 1.1 Bypass of RF input for downconverter. 0.9 This pin is RF input for downconverter designed as double balanced mixer ...
Page 4
... Ground for oscillator buffer amplifier and mixer of upconverter. Must be connected to the system ground with minimum inductance. Ground pattern on the board should be formed as wide as possible. (Track length should be kept as short as possible ...
Page 5
ABSOLUTE MAXIMUM RATINGS Supply Voltage V CC Power Dissipation package allowance Operating Temperature T opt Storage Temperature T stg RECOMMENDED OPERATING CONDITIONS PARAMETERS SYMBOL Supply Voltage V CC Operating Temperature T opt ELECTRICAL CHARACTERISTICS (T PARAMETERS 1 ...
Page 6
STANDARD CHARACTERISTIC FOR REFERENCE (T PARAMETERS UPCONVERTER BLOCK 3rd order intermodulation distortion DOWNCONVERTER BLOCK IF output 1 dB compression Local leakage at IF out Pin RF leakage at IF out Pin 2 ...
Page 7
TEST CIRCUIT (IF) Spectrum Analyzer 50 51 120 pF 1 500 120 pF 120 Signal Generator 50 Signal Generator (LO) 1 ...
Page 8
... TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD OSC IN NEC PC8100 OUT OSC OUT 8 IC MOUNTED SIDE 120 pF Trimer condenser 4.7 nH 120 COMPONENT MOUNTED SIDE 150 nH 120 pF 0 4.7 nF 120 pF 120 4.7 nF Data Sheet P10817EJ3V0DS00 ...
Page 9
TYPICAL PERFORMANCE (Unless otherwise specified V – Downconverter block – RF input frequency vs. Noise figure 15.0 Vcc = 2 sweep (–9 dBm +25 ˚ +80 ˚ –30 ˚C A ...
Page 10
Downconverter block – RF input level vs. IF output level and –10 –20 –30 Vcc = 4.5 V – 866 866 – 1016 MH –60 –70 ...
Page 11
Upconverter block – F input level vs. RF outpint level and –10 –20 –30 Vcc = 2.7 V – 150 150.8 MH – 1016 MH –60 T ...
Page 12
Downconverter block – P/S control voltage vs. Circuit Current 50 Vcc = 2 input signal 1.0 2.0 3.0 Power-save-control voltage V Supply voltage vs. Circuit Current 50 Vcc = V P/S ...
Page 13
TYPICAL APPLICATION CT2 BLOCK DIAGRAM RX SW PG131GR TX The application circuits and their parameters are for references only and are not intended for use in actual design-in's. PLL 0° F/F 90° PC8100GR PC8101GR Data Sheet P10817EJ3V0DS00 PC8100GR I DEMO ...
Page 14
PACKAGE DIMENSIONS 20 PIN PLASTIC SSOP (225 mil) (UNIT: mm 6.7 0.3 1.8 MAX. 1.5 0.1 0.65 +0.10 0.10 0.22 –0.05 0.1 0.1 NOTE Each lead centerline is located within 0. its true position (T.P.) at ...
Page 15
... Form a ground pattern as wide as possible to minimize ground impedance (to prevent undesired oscillation). (3) Keep the track length of the ground pins as short as possible. (4) Connect a bypass capacitor (e.g. 1 000 pF) to the V RECOMMENDED SOLDERING CONDITIONS This product should be soldered in the following recommended conditions. Other soldering method and conditions than the recommended conditions are to be consulted with our sales representatives ...
Page 16
... Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...