CY28410 Cypress Semiconductor, CY28410 Datasheet - Page 3

• Manufacturer Part Number: CY28410
• Description: Clock Generator for Intel Grantsdale Chipset
• Manufacturer: Cypress Semiconductor

Document #: 38-07593 Rev. *C
Frequency Select Pins (FS_A, FS_B and FS_C)
Host clock frequency selection is achieved by applying the
appropriate logic levels to FS_A, FS_B, FS_C inputs prior to
VTT_PWRGD# assertion (as seen by the clock synthesizer).
Upon VTT_PWRGD# being sampled low by the clock chip
(indicating processor VTT voltage is stable), the clock chip
Table 1. Frequency Select Table FS_A, FS_B and FS_C
Serial Data Interface
To enhance the flexibility and function of the clock synthesizer,
a two-signal serial interface is provided. Through the Serial
Data Interface, various device functions, such as individual
clock output buffers, can be individually enabled or disabled.
The registers associated with the Serial Data Interface initial-
izes to their default setting upon power-up, and therefore use
of this interface is optional. Clock device register changes are
normally made upon system initialization, if any are required.
The interface cannot be used during system operation for pow-
er management functions.
Table 2. Command Code Definition
Table 3. Block Read and Block Write Protocol
FS_C
MID
18:11
27:20
36:29
45:38
(6:0)
0
0
0
1
1
1
8:2
Bit
Bit
10
19
28
37
46
1
9
7
FS_B
Start
Slave address – 7 bits
Write
Acknowledge from slave
Command Code – 8 bits
Acknowledge from slave
Byte Count – 8 bits
(Skip this step if I
Acknowledge from slave
Data byte 1 – 8 bits
Acknowledge from slave
Data byte 2 – 8 bits
Acknowledge from slave
0 = Block read or block write operation, 1 = Byte read or byte write operation
Byte offset for byte read or byte write operation. For block read or block write operations, these bits should be
'0000000'
0
0
1
0
0
1
1
Block Write Protocol
FS_A
1
1
0
0
0
1
x
2
C_EN bit set)
Description
100 MHz
133 MHz
200 MHz
266 MHz
REF/2
REF/2
CPU
Hi-Z
100 MHz
100 MHz
100 MHz
100 MHz
REF/8
REF/8
SRC
Hi-Z
Description
PCIF/PCI
samples the FS_A, FS_B and FS_C input values. For all logic
levels of FS_A, FS_B and FS_C, VTT_PWRGD# employs a
one-shot functionality in that once a valid low on
VTT_PWRGD# has been sampled, all further VTT_PWRGD#,
FS_A, FS_B and FS_C transitions will be ignored, except in
test mode.
Data Protocol
The clock driver serial protocol accepts byte write, byte read,
block write, and block read operations from the controller. For
block write/read operation, the bytes must be accessed in se-
quential order from lowest to highest byte (most significant bit
first) with the ability to stop after any complete byte has been
transferred. For byte write and byte read operations, the sys-
tem controller can access individually indexed bytes. The off-
set of the indexed byte is encoded in the command code, as
described in Table 2.
The block write and block read protocol is outlined in Table 3
while Table 4 outlines the corresponding byte write and byte
read protocol. The slave receiver address is 11010010 (D2h).
33 MHz
33 MHz
33 MHz
33 MHz
REF/24
REF/24
18:11
27:21
37:30
Hi-Z
Bit
8:2
10
19
20
28
29
38
1
9
Start
Slave address – 7 bits
Write
Acknowledge from slave
Command Code – 8 bits
Acknowledge from slave
Repeat start
Slave address – 7 bits
Read = 1
Acknowledge from slave
Byte Count from slave – 8 bits
Acknowledge
14.318 MHz
14.318 MHz
14.318 MHz
14.318 MHz
REF0
Hi-Z
REF
REF
Block Read Protocol
Description
96 MHz
96 MHz
96 MHz
96 MHz
DOT96
REF
REF
Hi-Z
CY28410
Page 3 of 18
48 MHz
48 MHz
48 MHz
48 MHz
USB
REF
REF
Hi-Z