ADC08D1000EVAL National Semiconductor, ADC08D1000EVAL Datasheet - Page 18

• Manufacturer Part Number: ADC08D1000EVAL
• Description: High Performance/ Low Power/ Dual 8-Bit/ 1 GSPS A/D Converter
• Manufacturer: National Semiconductor

www.national.com
1.0 Functional Description
The ADC08D1000 is a versatile A/D Converter with an inno-
vative architecture permitting very high speed operation. The
controls available ease the application of the device to circuit
solutions. Optimum performance requires adherence to the
provisions discussed here and in the Applications Informa-
tion Section.
While it is generally poor practice to allow an active pin to
float, pins 4, 14 and 127 of the ADC08D1000 are designed to
be left floating without jeopardy. In all discussions throughout
this data sheet, whenever a function is called by allowing a
pin to float, connecting that pin to a potential of one half the
V
float.
1.1 OVERVIEW
The ADC08D1000 uses a calibrated folding and interpolating
architecture that achieves over 7.5 effective bits. The use of
folding amplifiers greatly reduces the number of comparators
and power consumption. Interpolation reduces the number
of front-end amplifiers required, minimizing the load on the
input signal and further reducing power requirements. In
addition to other things, on-chip calibration reduces the INL
bow often seen with folding architectures. The result is an
extremely fast, high performance, low power converter.
The analog input signal that is within the converter’s input
voltage range is digitized to eight bits at speeds of 200
MSPS to 1.6 GSPS, typical. Differential input voltages below
negative full-scale will cause the output word to consist of all
zeroes. Differential input voltages above positive full-scale
will cause the output word to consist of all ones. Either of
these conditions at either the "I" or "Q" input will cause the
OR (Out of Range) output to be activated. This single OR
output indicates when the output code from one or both of
the channels is below negative full scale or above positive
full scale.
Each of the two converters has a 1:2 demultiplexer that
feeds two LVDS output buses. The data on these buses
provide an output word rate on each bus at half the ADC
sampling rate and must be interleaved by the user to provide
output words at the full conversion rate.
The output levels may be selected to be normal or reduced.
Using reduced levels saves power but could result in erro-
neous data capture of some or all of the bits, especially at
higher sample rates and in marginally designed systems.
1.1.1 Self-Calibration
A self-calibration is performed upon power-up and can also
be invoked by the user upon command. Calibration trims the
100Ω analog input differential termination resistor and mini-
mizes full-scale error, offset error, DNL and INL, resulting in
maximizing SNR, THD, SINAD (SNDR) and ENOB. Internal
bias currents are also set with the calibration process. All of
this is true whether the calibration is performed upon power
up or is performed upon command. Running the self calibra-
tion is an important part of this chip’s functionality and is
required in order to obtain adequate performance. In addi-
tion to the requirement to be run at power-up, self calibration
must be re-run whenever the sense of the FSR pin is
changed. For best performance, we recommend that self
calibration be run 20 seconds or more after application of
power and whenever the operating ambient temperature
changes more than 30˚C since calibration was last per-
formed. See Section 2.4.2.2 for more information. Calibra-
A
supply voltage will have the same effect as allowing it to
18
tion can not be initiated or run while the device is in the
power-down mode. See Section 1.1.7 for information on the
interaction between Power Down and Calibration.
During the calibration process, the input termination resistor
is trimmed to a value that is equal to R
resistor is located between pin 32 and ground. R
3300 Ω
is trimmed to be 100 Ω. Because R
proper current for the Track and Hold amplifier, for the
preamplifiers and for the comparators, other values of R
should not be used. In normal operation, calibration is per-
formed just after application of power and whenever a valid
calibration command is given, which is holding the CAL pin
low for at least 10 input clock cycles, then hold it high for at
least another 10 input clock cycles. The time taken by the
calibration procedure is specified in the A.C. Characteristics
Table. Holding the CAL pin high upon power up will prevent
the calibration process from running until the CAL pin expe-
riences the above-mentioned 10 input clock cycles low fol-
lowed by 10 cycles high.
CalDly (pin 127) is used to select one of two delay times after
the application of power to the start of calibration. This
calibration delay is 2
1 GSPS) with CalDly low, or 2
2.15 seconds at 1 GSPS) with CalDly high. These delay
values allow the power supply to come up and stabilize
before calibration takes place. If the PD pin is high upon
power-up, the calibration delay counter will be disabled until
the PD pin is brought low. Therefore, holding the PD pin high
during power up will further delay the start of the power-up
calibration cycle. The best setting of the CalDly pin depends
upon the power-on settling time of the power supply.
The CalRun output is high whenever the calibration proce-
dure is running. This is true whether the calibration is done at
power-up or on-command.
1.1.2 Acquiring the Input
Data is acquired at the falling edge of CLK+ (pin 18) and the
digital equivalent of that data is available at the digital out-
puts 13 input clock cycles later for the DI and DQ output
buses and 14 input clock cycles later for the DId and DQd
output buses. There is an additional internal delay called t
before the data is available at the outputs. See the Timing
Diagram. The ADC08D1000 will convert as long as the input
clock signal is present. The fully differential comparator de-
sign and the innovative design of the sample-and-hold am-
plifier, together with self calibration, enables a very flat
SINAD/ENOB response beyond 1.0 GHz. The ADC08D1000
output data signaling is LVDS and the output format is offset
binary.
1.1.3 Control Modes
Much of the user control can be accomplished with several
control pins that are provided. Examples include initiation of
the calibration cycle, power down mode and full scale range
setting. However, the ADC08D1000 also provides an Ex-
tended Control mode whereby a serial interface is used to
access register-based control of several advanced features.
The Extended Control mode is not intended to be enabled
and disabled dynamically. Rather, the user is expected to
employ either the normal control mode or the Extended
Control mode at all times. When the device is in the Ex-
tended Control mode, pin-based control of several features
is replaced with register-based control and those pin-based
±
0.1%. With this value, the input termination resistor
25
input clock cycles (about 33.6 ms at
31
EXT
input clock cycles (about
EXT
is also used to set the
/ 33. This external
EXT
must be
EXT
OD