TA8492P/PG TOSHIBA [Toshiba Semiconductor], TA8492P/PG Datasheet
TA8492P/PG
Related parts for TA8492P/PG
TA8492P/PG Summary of contents
Page 1
... Three-Phase Full-Wave Brushless DC Motor Driver IC The TA8492P/ three-phase, full-wave, supply voltage-control motor driver IC. Features • Output current 1 (max) • Supply voltage control motor driver • CW/CCW/STOP function • Operating voltage range (opr (opr.) Block Diagram 3ST V CC ...
Page 2
... Function ⎯ ⎯ ⎯ ⎯ Output High Impedance TA8492P/PG 2006-3-2 ...
Page 3
... A (sink current SAT ( ( ( CMRH V STP ⎯ TA8492P/ Min Typ. Max ⎯ 5.0 7.0 ⎯ 6.0 9.0 ⎯ ) 2.5 CC ⎯ 1.35 1.7 ⎯ 0.4 0.6 ⎯ ⎯ 50 ⎯ ⎯ 50 ⎯ ⎯ 20 400 V ⎯ ⎯ ...
Page 4
... Make sure that the input amplitude does not p-p − 3 0.4 V. However, keep the voltage as close possible (Upper) (Lower) voltage. To reduce switching noise, connect a snubber capacitor to the S = 160°C (typ.) (according to design specification TA8492P/PG / 2006-3-2 ...
Page 5
... GND pins. Do not connect an input resistor to CC causes an output function error. Make sure the amplitude is p and GND lines since the IC may be destroyed S CC Recommended Remarks Value 4.7 µF ⎯ 4.7 µF ⎯ 4.7 µF (Note 3) ⎯ (Note 4) 5 TA8492P/PG (Stop mode) are narrow, STP 2006-3-2 ...
Page 6
... GND GND − + GND GND (6.01 V/5.99 V), check that the output function is at High level TA8492P/ − GND 3ST = GND 3ST = V 3ST − 2006-3-2 ...
Page 7
... GND (6.01 V/5.99 V) and check that the output function is “L” − GND GND − + GND GND TA8492P/ − − 2006-3-2 ...
Page 8
... − + GND GND (6.01 V/5.99 V) and check the output function GND. 3ST + + + , (6.01 V/5.99 V), fix the output function, then check (6.01 V/5.99 V) and check that the output function is forward mode TA8492P/ − − 2006-3-2 ...
Page 9
... V : Measure the I CMRH CMRH + (6.01 V/5.99 V) and check that the output function is reverse mode − GND GND − + GND GND gap between and 8.5 V. CMRH 9 TA8492P/PG + − 2006-3-2 ...
Page 10
... Note: Utmost care is necessary in the design of the output short-circuiting between outputs, air contamination faults, or faults due to improper grounding short-circuiting between contiguous pins TSD , TA8492P/ 12, 13 GND , and GND lines since the IC may be destroyed ...
Page 11
... Package Dimensions Weight: 1.11 g (typ.) 11 TA8492P/PG 2006-3-2 ...
Page 12
... Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. 12 TA8492P/PG 2006-3-2 ...
Page 13
... If the current sink capability of the power supply is small, the device’s motor power supply and output pins might be exposed to conditions beyond maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 13 TA8492P/ 2006-3-2 ...
Page 14
... TA8492P/PG 2006-3-2 ...