MHL0512D INTERPOINT [Interpoint Corporation Company], MHL0512D Datasheet - Page 2

• Manufacturer Part Number: MHL0512D
• Description: DC/DC CONVERTERS 5 VOLT INPUT
• Manufacturer: INTERPOINT [Interpoint Corporation Company]

MHL SERIES
15 WATT
Input Voltage
Output Power
Lead Soldering Temperature (10 sec per lead)
Storage Temperature Range (Case)
B4-18
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range
Case Operating Temperature (Tc)
Derating Output Power/Current
• 4 to 8 VDC
• 15 watts
• 300°C
• –55°C to +125°C
• 4 to 8 VDC continuous
• –55°C to +85°C full power
• –55°C to +115°C absolute
• Linearly from 100% at 85°C to 0% at 115° C
ABSOLUTE MAXIMUM RATINGS
Pin
1,2
9, 10
3
4
5
6
7
8
OUTPUT VOLTAGE
OUTPUT CURRENT
OUTPUT POWER
OUTPUT RIPPLE
LINE REGULATION
4 TO 8 V
LOAD REGULATION
NO LOAD TO FULL
CROSS REGULATION
INPUT VOLTAGE
INPUT CURRENT
INPUT RIPPLE CURRENT
EFFICIENCY
Notes
1. 95% of the maximum current or power is available from either output. The total of both outputs must not exceed the
2. The effect on the positive output when it is held at 50 mA while the negative output is varied from 50 to 950 mA.
PARAMETER
maximum specification.
The effect on the negative output when it is held at 50 mA while the positive output is varied from 50 to 950 mA.
Electrical Characteristics: 25°C Tc, 5 VDC Vin, 100% load, unless otherwise specified.
23002-001-DTS Rev A
All technical information is believed to be accurate, but no responsibility is
assumed for errors or omissions. Interpoint reserves the right to make changes in
products or specifications without notice. MHL Series is a trademark of Interpoint.
Copyright © 1994 - 1999 Interpoint. All rights reserved.
Positive Input
Positive Output
Output Common
Negative Output
No Connection
Case Ground
Inhibit
Input Common
IN
Designation
PIN OUT
1
1
2
Tc = –55°C TO +85°C
Tc = –55°C TO +85°C
DQ# 1018
CONDITIONS
BW = 1 MHz
FULL LOAD
FULL LOAD
INHIBITED
DC/DC C
NO LOAD
+V
–V
+V
–V
+V
–V
+V
–V
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
Dotted line outlines
flanged package
option.
Number of Outputs
(S = single, D = dual)
Output Voltage
Input Voltage
Case Option
(Non-flanged case has no designator in
this position)
Base Model
Screening
(Standard screening has no designator
in this position.)
MODEL NUMBERING KEY
11.88
11.88
MIN
—
—
—
—
—
—
—
—
—
—
—
—
—
—
4
ONVERTERS
MHL0512D
12.00
12.00
MHL
0.05
0.05
0.05
0.25
TYP
120
2.2
2.2
40
20
50
78
—
—
—
5
See Section B8, cases F4 and J5 for dimensions.
10
Squared corner and dot on
top of cover indicate pin one.
1
F
05 12
IGURE
12.12
12.12
MAX
4500
1.25
15.0
0.10
0.15
0.15
0.50
100
150
120
3.5
3.5
—
—
8
S
2
9
BOTTOM VIEW
2: P
F / ES
±14.85
14.85
MIN
IN
—
—
—
—
—
—
—
—
—
—
—
—
—
—
4
MHL
O
3
8
UT
MHL0515D
15.00
15.00
TYP
0.05
0.05
0.03
0.20
140
1.9
1.9
—
—
40
—
20
70
78
5
Output Voltage Temperature Coefficient
Input to Output Capacitance
Isolation
Conversion Frequency
4
7
• 150 ppm/°C, typical
• 80 pF typical
• 100 megohm minimum at 500 V
• 210 kHz, typical
TYPICAL CHARACTERISTICS
15.15
15.15
Inhibit TTL Open Collector
MAX
4500
1.00
15.0
0.10
0.15
0.10
0.40
120
180
150
3.0
3.0
—
—
8
• Logic low (output disabled)
• Referenced to input common
• Logic high (output enabled)
5
6
Open collector
mV p-p
mA p-p
UNITS
VDC
VDC
mA
INHIBIT
W
%
%
%
%
A