PCF2129AT NXP [NXP Semiconductors], PCF2129AT Datasheet - Page 33

no-image

PCF2129AT

Manufacturer Part Number
PCF2129AT
Description
Integrated RTC, TCXO and quartz crystal
Manufacturer
NXP [NXP Semiconductors]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PCF2129AT
Manufacturer:
NXP
Quantity:
3
Part Number:
PCF2129AT
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
PCF2129AT/1
Manufacturer:
NXP
Quantity:
12 246
Part Number:
PCF2129AT/1,518
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
PCF2129AT/1Ј¬512
Manufacturer:
PH3
Quantity:
3 040
Part Number:
PCF2129AT/2
0
Part Number:
PCF2129AT/2,518
Manufacturer:
NXP
Quantity:
100
Part Number:
PCF2129AT/2,518
Manufacturer:
NXP
Quantity:
30
Part Number:
PCF2129AT/2,518
Manufacturer:
NXP
Quantity:
250
Part Number:
PCF2129AT/2,518
Manufacturer:
NXP/恩智浦
Quantity:
20 000
NXP Semiconductors
PCF2129A_1
Product data sheet
8.11.1 Timestamp flag
8.11 Timestamp function
The PCF2129A has an active LOW timestamp input pin TS, internally pulled with an
on-chip pull-up resistor to the internal power supply of the device. It also has a timestamp
detection circuit which can detect two different events:
The timestamp function is enabled by default after power-on and it can be switched off by
setting the control bit TSOFF (register Timestp_ctl).
A most common application of the timestamp function is described in the application note
Ref. 3
See
1. input on the pin TS is driven to an intermediate level between the power supply and
2. input on the pin TS is driven to ground.
1. When the TS input pin is driven to an intermediate level between the power supply
2. When the TS input pin is driven to ground the following sequence occurs:
Fig 18. Timestamp detection with two push-buttons on one the TS pin (e.g. for tamper
ground.
and ground then the following sequence occurs:
a. The actual date and time are stored in the timestamp registers.
b. The timestamp flag TSF1 (register Control_1) is set.
c. If the TSIE bit (register Control_2) is active, an interrupt on the INT pin is
The TSF1 flag can be cleared by using the interface. Clearing the flag will clear the
interrupt. Once TSF1 is cleared it will only be set again when a new negative edge on
pin TS is detected.
a. The actual date and time are stored in the timestamp registers.
b. In addition to the TSF1 flag, the TSF2 flag (register Control_3) is set.
c. If the TSIE bit is active, an interrupt on the INT pin is generated.
Section 8.12.5
“AN10857”.
generated.
detection)
push-button 2
connected to
cover 2
for a description of interrupt generation from the timestamp function.
Rev. 01 — 13 January 2010
V
SS
R2 =
200 kΩ
± 5 %
Integrated RTC, TCXO and quartz crystal
push-button 1
connected to
cover 1
TS
1
2
3
4
5
6
7
8
PCF212xA
V
DD
R1 =
200 kΩ
± 20 %
013aaa176
PCF2129A
16
15
14
13
12
11
10
9
© NXP B.V. 2010. All rights reserved.
33 of 68

Related parts for PCF2129AT