X1286V14IZ INTERSIL [Intersil Corporation], X1286V14IZ Datasheet - Page 12
![no-image](/images/no-image-200.jpg)
X1286V14IZ
Manufacturer Part Number
X1286V14IZ
Description
Intersil Real Time Clock/Calendar/CPU Supervisor with EEPROM
Manufacturer
INTERSIL [Intersil Corporation]
Datasheet
1.X1286V14IZ.pdf
(25 pages)
AL1, AL0: Alarm bits—Volatile
These bits announce if either alarm 0 or alarm 1 match
the real time clock. If there is a match, the respective
bit is set to ‘1’. The falling edge of the last data bit in a
SR Read operation resets the flags. Note: Only the AL
bits that are set when an SR read starts will be reset.
An alarm bit that is set by an alarm occurring during an
SR read operation will remain set after the read opera-
tion is complete.
RWEL: Register Write Enable Latch—Volatile
This bit is a volatile latch that powers up in the LOW
(disabled) state. The RWEL bit must be set to “1” prior
to any writes to the Clock/Control Registers. Writes to
RWEL bit do not cause a nonvolatile write cycle, so
the device is ready for the next operation immediately
after the stop condition. A write to the CCR requires
both the RWEL and WEL bits to be set in a specific
sequence.
WEL: Write Enable Latch—Volatile
The WEL bit controls the access to the CCR and
memory array during a write operation. This bit is a
volatile latch that powers up in the LOW (disabled)
state. While the WEL bit is LOW, writes to the CCR or
any array address will be ignored (no acknowledge will
be issued after the Data Byte). The WEL bit is set by
writing a “1” to the WEL bit and zeroes to the other bits
of the Status Register. Once set, WEL remains set
until either reset to 0 (by writing a “0” to the WEL bit
and zeroes to the other bits of the Status Register) or
until the part powers up again. Writes to WEL bit do not
cause a nonvolatile write cycle, so the device is ready for
the next operation immediately after the stop condition.
RTCF: Real Time Clock Fail Bit—Volatile
This bit is set to a “1” after a total power failure. This is
a read only bit that is set by hardware (X1286 inter-
nally) when the device powers up after having lost all
power to the device (both V
The bit is set regardless of whether V
applied first. The loss of only one of the supplies does
not set the RTCF bit to “1”. On power up after a total
power failure, all registers are set to their default
states and the clock will not increment until at least
one byte is written to the clock register. The first valid
write to the RTC section after a complete power failure
resets the RTCF bit to “0” (writing one byte is suffi-
cient).
12
CC
and V
BACK
CC
or V
go to 0V).
BACK
is
X1286
Unused Bits:
This device does not use bits 3 or 4 in the SR, but
must have a zero in these bit positions. The Data Byte
output during a SR read will contain zeros in these bit
locations.
CONTROL REGISTERS
The Control Bits and Registers, described under this
section, are nonvolatile.
Block Protect Bits—BP2, BP1, BP0
The Block Protect Bits, BP2, BP1 and BP0, determine
which blocks of the array are write protected. A write to a
protected block of memory is ignored. The block protect
bits will prevent write operations to one of eight segments
of the array. The partitions are described in Table 3 .
Table 3. Block Protect Bits
Watchdog Timer Control Bits—WD1, WD0
The bits WD1 and WD0 control the period of the
Watchdog Timer. See Table 4 for options.
Table 4. Watchdog Timer Time-Out Options
WD1 WD0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
6000h - 7FFFh
4000h - 7FFFh
0000h - 7FFFh
0000h - 007Fh
0000h - 00FFh
0000h - 01FFh
0000h - 03FFh
Watchdog Time-Out Period
Addresses
Protected
X1286
None
1.75 seconds (default)
750 milliseconds
250 milliseconds
Disabled
None (default)
Array Lock
First 8 Pgs
First 2 pgs
First 4 pgs
First Page
Upper 1/4
Upper 1/2
Full Array
April 14, 2006
FN8101.1