HI5702-EV2 INTERSIL [Intersil Corporation], HI5702-EV2 Datasheet
HI5702-EV2
Related parts for HI5702-EV2
HI5702-EV2 Summary of contents
Page 1
... Refer to the HI5703, HI5746, or HI5767 data sheets for lower power consumption. Ordering Information PART NUMBER HI5702KCB HI5702JCB HI5702-EV2 Typical Application Schematic HI5702 3.25V V + (7) REF V - (8) 2 ...
Page 2
... Functional Block Diagram S/H 2-BIT FLASH + - X2 2-BIT FLASH + - X2 1-BIT FLASH AV AGND CC HI5702 BIAS STAGE 1 2-BIT DAC DIGITAL DELAY STAGE 9 DIGITAL ERROR CORRECTION 2-BIT DAC STAGE 10 DV DGND REF REF 4-1506 CLK CLOCK DFS D9 (MSB AND D4 D3 ...
Page 3
... Operating Conditions Temperature Range HI5702KCB/JCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. ...
Page 4
... POWER SUPPLY CHARACTERISTICS Supply Current Power Dissipation Offset Error PSRR Gain Error PSRR, FSE NOTES: 10. Parameter guaranteed by design or characterization and not production tested. 11. With the clock off. HI5702 = +5V 3.25V 2V REF REF Unless Otherwise Specified (Continued) ...
Page 5
... 10 10 LAT FIGURE 8. HI5702 INTERNAL CIRCUIT TIMING 1. 2.0V DATA 0.8V FIGURE 9. INPUT-TO-OUTPUT TIMING 4-1509 ...
Page 6
... INPUT FREQUENCY (MHz) FIGURE 12. SINAD vs INPUT FREQUENCY -40 -43 -46 -49 -52 - MSPS S -58 - MSPS S -64 -67 - INPUT FREQUENCY (MHz) FIGURE 14. THD vs INPUT FREQUENCY HI5702 MSPS 100 1 FIGURE 11. SFDR vs INPUT FREQUENCY MSPS ...
Page 7
... TEMPERATURE ( FIGURE 16. ENOB vs TEMPERATURE -40 - TEMPERATURE ( FIGURE 18. SUPPLY CURRENT vs TEMPERATURE 10 9.75 9.5 9.25 8.75 8.5 8.25 HI5702 (Continued 100 - FIGURE 17 MSPS 8.75 8.5 8. 100 o C) FIGURE 19. ENOB vs SAMPLE RATE WITH FIXED 12.5ns ...
Page 8
... Data Format Select (DFS) input. Analog Input, Differential Connection and 1 The analog input to the HI5702 is a differential input that can be configured in various ways depending on the signal source and the required level of performance. A fully differ- , are H ...
Page 9
... Since the HI5702 is powered by a single +5V analog supply, the analog input is limited to be between ground and +5V, which implies the common mode voltage can range of 0.625V to 4.375V. The performance of the ADC does not change sig- nificantly with the value of the common mode voltage. ...
Page 10
... HI5702 until the 511 to 512 transition occurs on the digital output. Next, set the analog input to the HI5702 to the desired posi- tive fullscale voltage. Adjust one side of the reference circuit up or down until the 1022 to 1023 transition occurs on the digital output of the converter ...
Page 11
... ADC which overdrives the input by 200mV, and measuring the number of cycles it takes for the output code to settle within 10-bit accuracy. HI5702 Full Power Input Bandwidth (FPBW) Full power bandwidth is the frequency at which the ampli- tude of the digitally reconstructed output has decreased 3dB below the amplitude of the input sine wave ...
Page 12
... HFA3102: Dual Long-Tailed Pair Transistor Array HFA3101: Gilbert Cell Transistor Array HFA1100: 850MHz Op Amp HI5702: 10-Bit, 40 MSPS, A/D Converter HI5703: Low Power, 10-Bit, 40 MSPS, A/D Converter HI5746: Low Power, CMOS, 10-Bit, 40 MSPS A/D Converter HI5767: Low Power, CMOS, 10-Bit, 40 MSPS A/D Converter, with Voltage Reference ...
Page 13
... Nitride + Undoped Silicon Glass (USG) Å, 8 Å Thickness: Nitride 4.2k USG k Å Å Total 12.2k 2k Metallization Mask Layout AV CC AGND V + REF V - REF HI5702 WORST CASE CURRENT DENSITY 1 A/cm TRANSISTOR COUNT: 4514 DIE DIMENSIONS: Silver Filled Epoxy HI5702 4-1517 CLK DGND D5 D6 ...
Page 14
... For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Office Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (321) 724-7000 FAX: (321) 724-7240 HI5702 EUROPE Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05 ...