X9260_06 INTERSIL [Intersil Corporation], X9260_06 Datasheet
![no-image](/images/no-image-200.jpg)
X9260_06
Related parts for X9260_06
X9260_06 Summary of contents
Page 1
Data Sheet Dual Digitally-Controlled (XDCP™) Potentiometers FEATURES • Dual–Two Separate Potentiometers • 256 Resistor Taps/pot–0.4% Resolution • SPI Serial Interface for Write, Read, and Transfer Operations of the Potentiometer • Wiper Resistance, 100Ω typical @ V+ = 5V, V- ...
Page 2
Ordering Information PART PART NUMBER MARKING X9260TS24I X9260TS I X9260TS24IZ (Note) X9260TS ZI X9260US24 X9260US X9260US24Z (Note) X9260US Z X9260TS24I-2.7 X9260TS G X9260TS24IZ-2.7 (Note) X9260TS ZG X9260US24-2.7 X9260US F X9260US24Z-2.7 (Note) X9260US ZF *Add "T1" suffix for tape and reel. ...
Page 3
CIRCUIT LEVEL APPLICATIONS • Vary the gain of a voltage amplifier • Provide programmable dc reference voltages for comparators and detectors • Control the volume in audio circuits • Trim out the offset voltage error in a voltage amplifier circuit ...
Page 4
PIN ASSIGNMENTS Pin (SOIC) Symbol ...
Page 5
CS LOW enables the X9260, placing it in the active power mode. It should be noted that after a power-up, a HIGH to LOW transition required prior to the start of any operation. Potentiometer Pins ...
Page 6
Figure 1. Detailed Potentiometer Block Diagram One of Two Potentiometers SERIAL DATA PATH FROM INTERFACE CIRCUITRY REGISTER 0 (DR0) REGISTER 2 (DR2) IF WCR = 00[H] THEN WCR = FF[H] THEN ...
Page 7
Table 5. Wiper Counter Register, WCR (8-bit), WCR[7:0]: Used to store the current wiper position (Volatile, V). WCR7 WCR6 WCR5 V V (MSB) Table 5. Data Register, DR (8-bit), Bit [7:0]: Used to store wiper positions or data (Nonvolatile, NV). ...
Page 8
DEVICE DESCRIPTION Instructions Four of the ten instructions are three bytes in length. These instructions are: – Read Wiper Counter Register – read the current wiper position of the selected potentiometer, – Write Wiper Counter Register – change current wiper ...
Page 9
Figure 2. Two-Byte Instruction Sequence CS SCK ID3 ID2 ID1 ID0 Device ID Figure 3. Three-Byte Instruction Sequence (Write) CS SCL ID3 ID2 ID1 ID0 0 0 Internal Device ID ...
Page 10
Figure 5. Three-Byte Instruction Sequence (Read Status Register) CS SCL ID3 ID2 ID1 ID0 Internal Device ID Address Figure 6. Increment/Decrement Instruction Sequence CS SCL ...
Page 11
Table 5. Instruction Set Instruction I3 Read Wiper Counter 1 Register Write Wiper Counter 1 Register Read Data Register 1 Write Data Register 1 XFR Data Register to 1 Wiper Counter Register XFR Wiper Counter 1 Register to Data Register ...
Page 12
INSTRUCTION FORMAT Read Wiper Counter Register (WCR) Device Type Device Identifier Addresses CS Falling Edge Write Wiper Counter Register (WCR) Device Type Device Identifier Addresses CS ...
Page 13
Global Transfer Wiper Counter Register (WCR) to Data Register (DR) Device Type Device CS Identifier Addresses Falling Edge Transfer Wiper Counter Register (WCR) to ...
Page 14
ABSOLUTE MAXIMUM RATINGS Temperature under bias ........................ -65 to +135°C Storage temperature ............................. -65 to +150°C Voltage on SCK, SCL or any address input with respect to V ................................. -1V to +7V SS Voltage on V+ (referenced ...
Page 15
POTENTIOMETER CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.) Symbol Parameter End to end resistance Power rating I Wiper current W R Wiper resistance W R Wiper resistance W Vv+ Voltage on V+ pin Vv- Voltage on V- pin V ...
Page 16
D.C. OPERATING CHARACTERISTICS Symbol Parameter I V supply current CC1 CC (active supply current CC2 CC (nonvolatile write current (standby Input leakage current LI I Output leakage current LO V Input HIGH voltage ...
Page 17
EQUIVALENT A.C. LOAD CIRCUIT 5V 1462Ω SO pin 2714Ω 100pF AC TIMING Symbol f SSI/SPI clock frequency SCK t SSI/SPI clock cycle rime CYC t SSI/SPI clock high rime WH t SSI/SPI clock low time WL t Lead time LEAD ...
Page 18
HIGH-VOLTAGE WRITE CYCLE TIMING Symbol t High-voltage write cycle time (store instructions) WR XDCP TIMING Symbol t Wiper response time after the third (last) power supply is stable WRPO t Wiper response time after instruction issued (all load instructions) WRL ...
Page 19
TIMING DIAGRAMS Input Timing CS t LEAD SCK MSB SI High Impedance SO Output Timing CS SCK t V MSB SO ADDR SI Hold Timing CS SCK HOLD 19 X9260 t CYC ...
Page 20
XDCP Timing (for All Load Instructions) CS SCK MSB SI VWx High Impedance SO Write Protect and Device Address Pins Timing X9260 ... t WRL ... (Any Instruction WPAH WPASU LSB FN8170.3 August ...
Page 21
APPLICATIONS INFORMATION Basic Configurations of Electronic Potentiometers V R THREE- TERMINAL POTENTIOMETER; VARIABLE VOLTAGE DIVIDER Application Circuits NONINVERTING AMPLIFIER – (1 OFFSET VOLTAGE ADJUSTMENT R 1 ...
Page 22
Application Circuits (continued) ATTENUATOR – -1/2 ≤ G ≤ +1/2 INVERTING AMPLIFIER ...
Page 23
Small Outline Plastic Packages (SOIC) N INDEX 0.25(0.010) H AREA E - SEATING PLANE - -C- α 0.10(0.004) 0.25(0.010 NOTES: 1. Symbols are defined in the ...