NG80960JA-16 INTEL [Intel Corporation], NG80960JA-16 Datasheet - Page 20

• Manufacturer Part Number: NG80960JA-16
• Description: EMBEDDED 32-BIT MICROPROCESSOR
• Manufacturer: INTEL [Intel Corporation]

80960JA/JF/JD/JT 3.3 V Microprocessor
Table 4.
20
Pin Description — Processor Control Signals, Test Signals and Power
VCCPLL
RESET
STEST
CLKIN
NAME
TRST
VCC5
FAIL
TDO
TMS
TCK
V
V
TDI
NC
CC
SS
TYPE
H(Q)
R(Q)
P(Q)
A(L)
S(L)
R(0)
P(1)
S(L)
A(L)
S(L)
HQ)
O
O
–
–
–
–
–
I
I
I
I
I
I
I
CLOCK INPUT provides the processor’s fundamental time base; both the processor
core and the external bus run at the CLKIN rate. All input and output timings are
specified relative to a rising CLKIN edge.
RESET initializes the processor and clears its internal logic. During reset, the
processor places the address/data bus and control output pins in their idle (inactive)
states.
During reset, the input pins are ignored with the exception of LOCK/ONCE, STEST
and HOLD.
The RESET pin has an internal synchronizer. To ensure predictable processor
initialization during power up, RESET must be asserted a minimum of 10,000 CLKIN
cycles with V
a minimum of 15 cycles.
SELF TEST enables or disables the processor’s internal self-test feature at
initialization. STEST is examined at the end of reset. When STEST is asserted, the
processor performs its internal self-test and the external bus confidence test. When
STEST is deasserted, the processor performs only the external bus confidence test.
0 = self test disabled
1 = self test enabled
FAIL indicates a failure of the processor’s built-in self-test performed during
initialization. FAIL is asserted immediately upon reset and toggles during self-test to
indicate the status of individual tests:
0 = self test failed
1 = self test passed
TEST CLOCK is a CPU input which provides the clocking function for IEEE 1149.1
Boundary Scan Testing (JTAG). State information and data are clocked into the
processor on the rising edge; data is clocked out of the processor on the falling edge.
TEST DATA INPUT is the serial input pin for JTAG. TDI is sampled on the rising
edge of TCK, during the SHIFT-IR and SHIFT-DR states of the Test Access Port.
TEST DATA OUTPUT is the serial output pin for JTAG. TDO is driven on the falling
edge of TCK during the SHIFT-IR and SHIFT-DR states of the Test Access Port. At
other times, TDO floats. TDO does not float during ONCE mode.
TEST RESET asynchronously resets the Test Access Port (TAP) controller function
of IEEE 1149.1 Boundary Scan testing (JTAG). When using the Boundary Scan
feature, connect a pulldown resistor between this pin and V
this pin must be connected to V
“Connection Recommendations” on page 40.
TEST MODE SELECT is sampled at the rising edge of TCK to select the operation of
the test logic for IEEE 1149.1 Boundary Scan testing.
POWER pins intended for external connection to a V
PLL POWER is a separate V
is intended for external connection to the V
add a simple bypass filter circuit to reduce noise-induced clock jitter and its effects
on timing relationships.
5 V REFERENCE VOLTAGE input is the reference voltage for the 5 V-tolerant I/O
buffers. This signal should be connected to +5 V for use with inputs which exceed
3.3 V. If all inputs are from 3.3 V components, this pin should be connected to 3.3 V.
GROUND pins intended for external connection to a V
NO CONNECT pins. Do not make any system connections to these pins.
• When self-test passes, the processor deasserts FAIL and begins operation from
• When self-test fails, the processor asserts FAIL and then stops executing.
user code.
CC
and CLKIN stable. On a warm reset, RESET should be asserted for
CC
SS
supply pin for the phase lock loop clock generator. It
; however, no resistor is required. See Section 4.3,
DESCRIPTION
CC
Advance Information Datasheet
board plane. In noisy environments,
CC
SS
board plane.
board plane.
SS
. If TAP is not used,