DP83848J_07 NSC [National Semiconductor], DP83848J_07 Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
DP83848J_07
Manufacturer Part Number
DP83848J_07
Description
Manufacturer
NSC [National Semiconductor]
Datasheet
1.DP83848J_07.pdf
(78 pages)
- Current page: 10 of 78
- Download datasheet (2Mb)
www.national.com
1.3 CLOCK INTERFACE
RX_ER
RXD_0
RXD_1
RXD_2
RXD_3
CRS/CRS_DV
COL
X1
X2
Signal Name
Signal Name
S, O, PU
S, O, PD
S, O, PU
S, O, PU
Type
Type
O
I
Pin #
Pin #
34
36
37
38
39
33
35
28
27
MII RECEIVE ERROR: Asserted high synchronously to RX_CLK
to indicate that an invalid symbol has been detected within a re-
ceived packet in 100 Mb/s mode.
RMII RECEIVE ERROR: Assert high synchronously to X1 when-
ever it detects a media error and RX_DV is asserted in 100 Mb/s
mode.
This pin is not required to be used by a MAC, in either MII or RMII
mode, since the Phy is required to corrupt data on a receive error.
MII RECEIVE DATA: Nibble wide receive data signals driven syn-
chronously to the RX_CLK, 25 MHz for 100 Mb/s mode, 2.5 MHz
for 10 Mb/s mode). RXD[3:0] signals contain valid data when
RX_DV is asserted.
RMII RECEIVE DATA: 2-bits receive data signals, RXD[1:0], driv-
en synchronously to the X1 clock, 50 MHz.
MII CARRIER SENSE: Asserted high to indicate the receive me-
dium is non-idle.
RMII CARRIER SENSE/RECEIVE DATA VALID: This signal
combines the RMII Carrier and Receive Data Valid indications.
For a detailed description of this signal, see the RMII Specifica-
tion.
MII COLLISION DETECT: Asserted high to indicate detection of
a collision condition (simultaneous transmit and receive activity)
in 10 Mb/s and 100 Mb/s Half Duplex Modes.
While in 10BASE-T Half Duplex mode with heartbeat enabled this
pin is also asserted for a duration of approximately 1µs at the end
of transmission to indicate heartbeat (SQE test).
In Full Duplex Mode, for 10 Mb/s or 100 Mb/s operation, this sig-
nal is always logic 0. There is no heartbeat function during 10
Mb/s full duplex operation.
RMII COLLISION DETECT: Per the RMII Specification, no COL
signal is required. The MAC will recover CRS from the CRS_DV
signal and use that along with its TX_EN signal to determine col-
lision.
CRYSTAL/OSCILLATOR INPUT: This pin is the primary clock
reference input for the DP83848J and must be connected to a 25
MHz 0.005% (+50 ppm) clock source. The DP83848J supports ei-
ther an external crystal resonator connected across pins X1 and
X2, or an external CMOS-level oscillator source connected to pin
X1 only.
RMII REFERENCE CLOCK: This pin is the primary clock refer-
ence input for the RMII mode and must be connected to a 50 MHz
0.005% (+50 ppm) CMOS-level oscillator source.
CRYSTAL OUTPUT: This pin is the primary clock reference out-
put to connect to an external 25 MHz crystal resonator device.
This pin must be left unconnected if an external CMOS oscillator
clock source is used.
10
Description
Description
Related parts for DP83848J_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![SFTB](/images/no-image3.png)
Part Number:
Description:
Thin SOT23 1A Load Step-Down DC-DC Regulator
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3603N](/images/no-image3.png)
Part Number:
Description:
TRI-STATE Dual Receiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS36149N](/images/no-image3.png)
Part Number:
Description:
Hex MOS Drivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3654N](/images/no-image3.png)
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3669N](/images/no-image3.png)
Part Number:
Description:
Quad High Current Peripheral Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3691N](/images/no-image3.png)
Part Number:
Description:
(RS-422/RS-423) Line Drivers with TRI-STATE Outputs
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3695TJ](/images/no-image3.png)
Part Number:
Description:
Multipoint RS485/RS422 Transceivers/Repeaters
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS36C279TM](/images/no-image3.png)
Part Number:
Description:
Low Power EIA-RS-485 Transceiver with Sleep Mode
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3884AVF](/images/no-image3.png)
Part Number:
Description:
BTL Handshake Transceiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![MM5034N](/images/no-image3.png)
Part Number:
Description:
Octal 80-Bit Static Shift Register
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![MM53143J](/images/no-image3.png)
Part Number:
Description:
PUSH BUTTON PULSE DIALER CIRCUITS
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![MM54C914J](/images/no-image3.png)
Part Number:
Description:
Hex Schmitt Trigger with Extended Input Voltage
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![MM58167](/images/no-image3.png)
Part Number:
Description:
Microprocessor Real Time Clock
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS75108M](/images/no-image3.png)
Part Number:
Description:
Dual Line Receivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS75113M](/images/no-image3.png)
Part Number:
Description:
Dual TRI-STATE Differential Line Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet: