DP83848J_07 NSC [National Semiconductor], DP83848J_07 Datasheet - Page 35
![no-image](/images/no-image-200.jpg)
DP83848J_07
Manufacturer Part Number
DP83848J_07
Description
Manufacturer
NSC [National Semiconductor]
Datasheet
1.DP83848J_07.pdf
(78 pages)
- Current page: 35 of 78
- Download datasheet (2Mb)
5.4 POWER FEEDBACK CIRCUIT
To ensure correct operation for the DP83848J, parallel
caps with values of 10 µF (Tantalum) and 0.1 µF should be
placed close to pin 19 (PFBOUT) of the device.
Pin 16 (PFBIN1) and pin 30 (PFBIN2) must be connected
to pin 19 (PFBOUT), each pin requires a small capacitor
(0.1 µF). See Figure 13 below for proper connections.
5.5 POWER DOWN
The device can be put in a Power Down mode by setting bit
11 (Power Down) in the Basic Mode Control Register,
BMCR (0x00h).
Pin 30 (PFBIN2)
Pin 19 (PFBOUT)
Pin 16 (PFBIN1)
Figure 13. Power Feedback Connection
0.1 µF
0.1 µF
10 µF
+
-
0.1µF
35
5.6 ENERGY DETECT MODE
When Energy Detect is enabled and there is no activity on
the cable, the DP83848J will remain in a low power mode
while monitoring the transmission line. Activity on the line
will cause the DP83848J to go through a normal power up
sequence. Regardless of cable activity, the DP83848J will
occasionally wake up the transmitter to put ED pulses on
the line, but will otherwise draw as little power as possible.
Energy detect functionality is controlled via register Energy
Detect Control (EDCR), address 0x1Dh.
6.0 Reset Operation
The DP83848J includes an internal power-on reset (POR)
function and does not need to be explicitly reset for normal
operation after power up. If required during normal opera-
tion, the device can be reset by a hardware or software
reset.
6.1 HARDWARE RESET
A hardware reset is accomplished by applying a low pulse
(TTL level), with a duration of at least 1 µs, to the
RESET_N. This will reset the device such that all registers
will be reinitialized to default values and the hardware con-
figuration values will be re-latched into the device (similar
to the power-up/reset operation).
6.2 SOFTWARE RESET
A software reset is accomplished by setting the reset bit
(bit 15) of the Basic Mode Control Register (BMCR). The
period from the point in time when the reset bit is set to the
point in time when software reset has concluded is approx-
imately 1 µs.
The software reset will reset the device such that all regis-
ters will be reset to default values and the hardware config-
www.national.com
Related parts for DP83848J_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![SFTB](/images/no-image3.png)
Part Number:
Description:
Thin SOT23 1A Load Step-Down DC-DC Regulator
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3603N](/images/no-image3.png)
Part Number:
Description:
TRI-STATE Dual Receiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS36149N](/images/no-image3.png)
Part Number:
Description:
Hex MOS Drivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3654N](/images/no-image3.png)
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3669N](/images/no-image3.png)
Part Number:
Description:
Quad High Current Peripheral Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3691N](/images/no-image3.png)
Part Number:
Description:
(RS-422/RS-423) Line Drivers with TRI-STATE Outputs
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3695TJ](/images/no-image3.png)
Part Number:
Description:
Multipoint RS485/RS422 Transceivers/Repeaters
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS36C279TM](/images/no-image3.png)
Part Number:
Description:
Low Power EIA-RS-485 Transceiver with Sleep Mode
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS3884AVF](/images/no-image3.png)
Part Number:
Description:
BTL Handshake Transceiver
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![MM5034N](/images/no-image3.png)
Part Number:
Description:
Octal 80-Bit Static Shift Register
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![MM53143J](/images/no-image3.png)
Part Number:
Description:
PUSH BUTTON PULSE DIALER CIRCUITS
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![MM54C914J](/images/no-image3.png)
Part Number:
Description:
Hex Schmitt Trigger with Extended Input Voltage
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![MM58167](/images/no-image3.png)
Part Number:
Description:
Microprocessor Real Time Clock
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS75108M](/images/no-image3.png)
Part Number:
Description:
Dual Line Receivers
Manufacturer:
NSC [National Semiconductor]
Datasheet:
![DS75113M](/images/no-image3.png)
Part Number:
Description:
Dual TRI-STATE Differential Line Driver
Manufacturer:
NSC [National Semiconductor]
Datasheet: