ISD2500 ETC1 [List of Unclassifed Manufacturers], ISD2500 Datasheet
ISD2500
Related parts for ISD2500
ISD2500 Summary of contents
Page 1
... Directly cascadable for longer durations • Automatic Power-Down (Push-Button Mode) – Standby current 1 A (typical) • Zero-power message storage – Eliminates battery backup circuits ISD2500 SERIES SUMMARY Part Number ISD2560 ISD2575 ISD2590 ISD25120 ISD2532* ISD2540* ISD2548* ISD2564* Information Storage Devices, Inc ...
Page 2
... Increasing the duration within a product series decreases the sampling frequency and bandwidth, which affects sound quality. Please refer to the ISD2500 Series Summary table on page 1-79 to compare filter pass band and product durations. The speech samples are stored directly into on- chip nonvolatile memory without the digitization and compression associated with other solutions ...
Page 3
... Programming The ISD2500 Series is also ideal for playback-only applications, where single or multiple messages are referenced through buttons, switches microcontroller. Once the desired message config- uration is created, duplicates can easily be generated via an ISD programmer ...
Page 4
... A nonvolatile marker is automatically inserted at the end of each recorded message. It remains there until the message is recorded over. The EOM output pulses LOW for a period of T the end of each message. In addition, the ISD2500 Series has an internal V detect circuit to maintain message integrity CC should V goes LOW and the device is fixed in Playback-only mode ...
Page 5
... ANA IN pin directly. External Clock Input (XCLK) The external clock input for the ISD2500 devices internal has an internal pull-down device. These devices are configured at the factory with an internal sam- pling clock frequency centered to Advance information: ISD2532/40/48/64 devices ...
Page 6
... IF THE XCLK IS NOT USED THIS INPUT MUST BE CON- . NECTED TO GROUND Speaker Outputs (SP+/SP-) All devices in the ISD2500 Series include an on- chip differential speaker driver, capable of driving 50 milliwatts into 16 from AUX IN (12.2 mW from memory). The speaker outputs are held at V record and power down therefore not possible to parallel speaker outputs of multiple ISD2500 devices or the outputs of other speaker drivers ...
Page 7
... These are described in detail below. The opera- tional modes use the address pins on the ISD2500 devices, but are mapped outside the valid address range. When the two Most Significant Bits (MSBs) ...
Page 8
... EOM marker. The M4 Operational Mode inhibits the address pointer reset on EOM, allowing mes- sages to be played back consecutively. M5 — CE-Level Activated The default mode for ISD2500 devices is for edge-activated on Playback and level-activated on Record. The M5 Operational Mode causes the CE pin to be interpreted as level-activated as opposed to edge-activated during Playback ...
Page 9
... Recording and Playback systems. To ensure the highest quality voice reproduction impor- tant that good audio design practices on layout and power supply decoupling be followed. See the ISD Application Notes and Design Manual in this book for details. Advance information: ISD2532/40/48/64 devices. * ISD2500 Series 1 1–87 ...
Page 10
... HIGH run indicator, and can be used to drive an LED indicating a Record or Playback operation is in progress. Devices in the Push-Button mode can- not be cascaded. Looping Mode The ISD2500 Series can loop with a message that completely fills the memory space. NOTE Additional descriptions of ISD2500 device functionality and application examples are provided in the ISD Application Notes and Design Manual in this book ...
Page 11
... SET P/R PD Don't Care A0-A9 Don't Care T SET SP+/– OVF EOM T PUD T CE Don't Care T PDH T HOLD Don't Care T OVF T CE Don't Care T PDH T HOLD Don't Care T T EOM Advance information: ISD2532/40/48/64 devices. * ISD2500 Series T T PDS PDR PDP PDS OVF 1–89 ...
Page 12
... ISD2500 Series ABSOLUTE MAXIMUM RATINGS (PACKAGED PARTS) Condition Junction temperature Storage temperature range Voltage applied to any pin Voltage applied to any pin (Input current limited to 20 mA) Lead temperature (soldering – 10 seconds NOTE: Stresses above those listed may cause permanent -1 damage to the device. Exposure to the absolute maximum ratings may affect device reliability ...
Page 13
... KHz 4.0 KHz 3.4 KHz 2.7 KHz 2.3 KHz 1.7 KHz 3.4 KHz 2.7 KHz 2.3 KHz 1.7 KHz Advance information: ISD2532/40/48/64 devices. * ISD2500 Series Conditions AGC = 0.0 V AGC = 2 Conditions (7) (7) (7) (7) (7) (7) (7) (7) (3) ( Roll-Off Point (3) ( Roll-Off Point (3) ( Roll-Off Point (3) ( Roll-Off Point ...
Page 14
... ISD2500 Series AC PARAMETERS (PACKAGED PARTS) – CONTINUED Symbol Characteristic T Record REC Duration T Playback PLAY Duration - Pulse Width CE T Control/Address Setup Time SET T Control/Address Hold Time HOLD T Power-Up Delay PUD T PD Pulse PDR Width Record 1–92 Advance information: ISD2532/40/48/64 devices. * (2) (1) ...
Page 15
... V p– 1.25 V =12.2 mW, typical. OUT Advance information: ISD2532/40/48/64 devices. * ISD2500 Series Conditions ( KHz ( EXT R = 600 EXT (5) Peak-to-Peak Peak-to-Peak Peak-to-Peak EXT 1–93 ...
Page 16
... ISD2500 Series TYPICAL PARAMETER VARIATION WITH VOLTAGE AND TEMPERATURE (PACKAGED PARTS) RECORD MODE OPERATING CURRENT ( -40 25 Temperature (C) TOTAL HARMONIC DISTORTION 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -40 25 Temperature (C) 5.5 Volts 4.5 Volts 1–94 Advance information: ISD2532/40/48/64 devices 1.2 1.0 0.8 0.6 0.4 0 -40 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 -40 Product Data Sheets STANDBY CURRENT (I ...
Page 17
... Max 0.8 2.0 0.4 V –0.4 CC 2.4 V –1.0 V –0 130 2 Advance information: ISD2532/40/48/64 devices. * ISD2500 Series Value +50 C ( CCA CCD = SSA SSD Units Conditions 4 – ...
Page 18
... ISD2500 Series DC PARAMETERS (DIE) – CONTINUED Symbol Parameters A Preamp Gain 1 PRE1 A Preamp Gain 2 PRE2 A AUX IN/SP+ Gain AUX A ANA IN to SP+/- Gain ARP R AGC Output Resistance AGC NOTES: 1. Typical values @ All Min/Max limits are guaranteed by ISD via electrical testing or characterization. Not all specifications are 100% tested. ...
Page 19
... Advance information: ISD2532/40/48/64 devices. * ISD2500 Series Conditions (7) (7) (7) (7) (7) Commercial Operation (7) Commercial Operation (7) Commercial Operation (7) Commercial Operation 1 Commercial Operation Commercial Operation Commercial Operation Commercial Operation (6) 1–97 ...
Page 20
... ISD2500 Series AC PARAMETERS (DIE) – CONTINUED Symbol Characteristic T EOM Pulse Width EOM T Overflow Pulse Width OVF THD Total Harmonic Distortion P Speaker Output Power OUT V Voltage Across Speaker Pins OUT -1 V MIC Input Voltage IN1 V ANA IN Input Voltage IN2 V Aux Input Voltage ...
Page 21
... TYPICAL PARAMETER VARIATION WITH VOLTAGE AND TEMPERATURE (DIE) RECORD MODE OPERATING CURRENT ( Temperature (C) TOTAL HARMONIC DISTORTION 0.7 0.6 0.5 0.4 0.3 0.2 0 Temperature (C) 6.5 Volts 5.5 Volts STANDBY CURRENT ( 1.0 0.8 0.6 0.4 0 Temperature (C) OSCILLATOR STABILITY 0.2 0 -0.2 -0.4 -0.6 -0.8 -1 Temperature (C) 4.5 Volts Advance information: ISD2532/40/48/64 devices. * ISD2500 Series ) 1–99 ...
Page 22
... ISD2500 Series ISD2500 APPLICATION EXAMPLE – DESIGN SCHEMATIC 100 K CHIP ENABLE POWER DOWN PLAYBACK/RECORD -1 NOTES: * Pin identifications for the ISD2532/40/48/64 devices which differ from those of the ISD2560/75/90/120 devices are indicated desired, pin 18 (PDIP package) may be left unconnected (microphone preamplifier noise will be higher). In this case, pin 18 must not be tied to any other signal or voltage ...
Page 23
... Push-Button mode and message cueing are used. The microcontroller is a 16-pin version with enough port pins for buttons, an LED, and the ISD2500 Series device. The software can be written to use three buttons: one each for play and record, and one for message selection. ...
Page 24
... ISD2500 Series ISD2500 APPLICATION EXAMPLE – MICROCONTROLLER/ISD2500 INTERFACE MC68HC705K1A PB0 OSC1 PB1 OSC2 PA0 RESET PA1 IRQ PA2 U 1 PA3 PA4 V DD PA5 PA6 V SS PA7 -1 NOTES: * Pin identifications for the ISD2532/40/48/64 devices which differ from those of the ISD2560/75/90/120 devices are indicated. ...
Page 25
... Product Data Sheets ISD2500 APPLICATION EXAMPLE – PUSH-BUTTON 100 K 100 START/PAUSE S2 STOP/RESET PLAYBACK/RECORD NOTES: * Pin identifications for the ISD2532/40/48/64 devices which differ from those of the ISD2560/75/90/120 devices are indicated. ** For more details, please refer to the ISD Application Notes and Design Manual. ...
Page 26
... ISD2500 Series APPLICATION EXAMPLE – PASSIVE COMPONENT FUNCTIONS Part R2 Release time constant R4 Series limiting resistor R6, R7 Pull-up and pull-down resistors C1, C4, C5 Power supply capacitors C2 Attack/Release time constant C3 Low-frequency cutoff capacitor PUSH-BUTTON PARAMETERS -1 Symbol Characteristic T CE Pulse Width [Start/Pause Control/Address Setup Time ...
Page 27
... SET T PAUSE PUD (4, 5) (6, 7) "Pause" "Start" SET T PAUSE PUD ( PUD Advance information: ISD2532/40/48/64 devices. * ISD2500 Series "Stop" T SET T T SET (8) "Stop" T SET T T SET (8) 1–105 1 ...
Page 28
... Duration Seconds Seconds Seconds Seconds Seconds - Seconds Seconds 120 = 120 Seconds When ordering ISD2500 Series devices, please refer to the following valid part numbers. Part Number ISD2560E ISD2560EI ISD2560P ISD2560PI ISD2560S ISD2560SI ISD2560T ISD2560TI ISD2560X For the latest product information, access ISD’ ...