AT88SC1616C-WI ATMEL [ATMEL Corporation], AT88SC1616C-WI Datasheet
AT88SC1616C-WI
Related parts for AT88SC1616C-WI
AT88SC1616C-WI Summary of contents
Page 1
... Patent) ISO Module Contact Standard Package Pin Note: This is a summary document. A complete document is available under NDA. For more information, please contact your local Atmel sales office. CryptoMemory 16 Kbit AT88SC1616C Summary Rev. 2030IS–SMIC–04/07 1 ...
Page 2
... ISO 7816-3. Through dynamic and symmetric mutual authentication, data encryption, and the use of encrypted checksums, the AT88SC1616C provides a secure place for storage of sensi- tive information within a system. With its tamper detection circuits, this information remains safe even under attack. A 2-wire serial interface running at 1.0 MHz is used for fast and efficient communications with devices that may be individually addressed ...
Page 3
... SCL/CLK input is used to positive edge clock data into the device and nega- tive edge clock data out of the device. The AT88SC1616C provides an ISO 7816-3 compliant asynchronous answer to reset sequence. When the reset sequence is activated, the device will output the data pro- grammed into the 64-bit answer-to-reset register ...
Page 4
... V SDA/IO Output Low Voltage OL I SDA/IO Output High Current OH Note min and V max are reference only and are not tested AT88SC1616C 4 = +2.7 to 5.5V Test Condition Async READ at 3.57MHz Async WRITE at 3.57MHz Synch READ at 1MHz Synch WRITE at 1MHz GND ...
Page 5
... Data Out Hold Time DH t Write Cycle Time (at 25° Write Cycle Time WR 2030IS–SMIC–04/07 = +2.7 to 5.5V, CC Min Range: +4.5 - 5.5V Range: +2.7 - 3.3V 200 200 10 100 200 20 AT88SC1616C Max Units 5 MHz 4 MHz 1 MHz period period ...
Page 6
... SCL SDA 8th BIT WORDn AT88SC1616C 6 CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an exter- nal device. Data on the SDA pin may change only during SCL low time periods (see Figure 5 on page 7). Data changes during SCL high periods will indicate a start or stop condition as defined below ...
Page 7
... Figure 5. Data Validity Figure 6. Start and Stop Definitions Figure 7. Output Acknowledge 2030IS–SMIC–04/07 AT88SC1616C 7 ...
Page 8
... Control Logic Configuration Memory AT88SC1616C 8 The EEPROM user memory is divided into 16 zones of 1024 bits each. Multiple zones allow for different types of data or files to be stored in different zones. Access to the user zones is allowed only after security requirements have been met. These security requirements are defined by the user during the personalization of the device in the con- figuration memory ...
Page 9
... AR10 AR13 PR13 AR14 Issuer Code For Authentication and Encryption use For Authentication and Encryption use PAC PAC PAC PAC PAC PAC PAC PAC Reserved AT88SC1616C $ Card Manufacturer Code PR2 AR3 PR3 PR6 AR7 PR7 PR10 AR11 PR11 PR14 AR15 ...
Page 10
... Fuses are designed for the module manufacturer, card manufacturer and card issuer and should be blown in sequence, although all programming of the device and blowing of the fuses may be performed at one final step. The AT88SC1616C supports two different communication protocols. • Smart Card Applications: The asynchronous protocol defined by ISO 7816-3 is used for compatibility with the industry’ ...
Page 11
... If a user zone is configured in the write lock mode, the lowest address byte of an 8-byte page constitutes a write access byte for the bytes of that page. Example: The write lock byte at $080 controls the bytes from $080 to $087. AT88SC1616C ...
Page 12
... Password Verification Authentication Protocol AT88SC1616C xxxx xxxx xxxx xxxx locked The write lock byte may also be locked by writing its least significant (rightmost) bit to “0”. Moreover, when write lock mode is activated, the write lock byte can only be pro- grammed – ...
Page 13
... Checksum (CS) VERIFY CS Write DATA The AT88SC1616C implements a data validity check function in the form of a check- sum, which may function in standard, authentication or encryption modes. In the standard mode, the checksum is implemented as a Modification Detection Code (MDC), in which the host may read an MDC from the device in order to verify that the data sent was received correctly ...
Page 14
... CryptoMemory using simple write and read commands. To gain access to the configuration memory, the secure code must first be successfully presented. For the AT88SC1616C device, the secure code is $20 0C E0. After writing and verifying data in the configuration memory, the security fuses must be blown to lock this information in the device ...
Page 15
... Ordering Information Ordering Code Package AT88SC1616C-MJ M2 – J Module AT88SC1616C-MP M2 – P Module AT88SC1616C-PU 8P3 AT88SC1616C-SU 8S1 AT88SC1616C-WI 7 mil wafer (1) Package Type M2 – J Module M2 – P Module 8P3 8S1 Note: 1. Formal drawings may be obtained from an Atmel sales office. 2030IS–SMIC–04/07 Voltage Range 2.7V–5.5V 2.7V– ...
Page 16
... Pitch: 14.25 mm *Note: The module dimensions listed refer to the dimensions of the exposed metal contact area. The actual dimensions of the module after excise or punching from the carrier tape are generally 0.4 mm greater in both directions (i.e., a punched M2 module will yield 13.0 x 11.8 mm). AT88SC1616C 16 Ordering Code: MP 8.5 [mm] Module Size: M2 Dimension*: 12 ...
Page 17
... Colorado Springs, CO 80906 R 2030IS–SMIC–04/ TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) AT88SC1616C Ø Ø END VIEW COMMON DIMENSIONS (Unit of Measure = mm) MIN SYMBOL NOM MAX A 1.35 – ...
Page 18
... E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm). 2325 Orchard Parkway San Jose, CA 95131 R AT88SC1616C ...
Page 19
... Doc. Rev. Date Comments 2030IS 4/13/07 Final release version 2030IS 1/25/07 Replaced User Zone, Configuration Memory, and Write Locks Example tables with new information 2030IS 1/2007 Implemented revision history. Removed Industrial packages 8P3, 8S1, 8Y4. Removed 8Y4 offering from datasheet. AT88SC1616C 19 ...
Page 20
... Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80 Literature Requests www.atmel.com/literature ® ® , CryptoMemory and others, are Printed on recycled paper. 2030IS–SMIC–04/07 ...