LT3690 LINER [Linear Technology], LT3690 Datasheet - Page 10

no-image

LT3690

Manufacturer Part Number
LT3690
Description
42V, 2.5A Synchronous Step-Down Regulator
Manufacturer
LINER [Linear Technology]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LT3690EUFE
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT3690EUFE
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT3690EUFE#TRPBF
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
LT3690EUFE#TRPBF
0
Part Number:
LT3690HUFE
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT3690HUFE
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT3690IUFE
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT3690IUFE
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT3690IUFE#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT3690MPUFE
Manufacturer:
LT
Quantity:
10 000
LT8610
OPERATION
The LT8610 is a monolithic, constant frequency, current
mode step-down DC/DC converter. An oscillator, with
frequency set using a resistor on the RT pin, turns on
the internal top power switch at the beginning of each
clock cycle. Current in the inductor then increases until
the top switch current comparator trips and turns off the
top power switch. The peak inductor current at which
the top switch turns off is controlled by the voltage on
the internal VC node. The error amplifier servos the VC
node by comparing the voltage on the V
internal 0.97V reference. When the load current increases
it causes a reduction in the feedback voltage relative to
the reference leading the error amplifier to raise the VC
voltage until the average inductor current matches the new
load current. When the top power switch turns off, the
synchronous power switch turns on until the next clock
cycle begins or inductor current falls to zero. If overload
conditions result in more than 3.3A flowing through the
bottom switch, the next clock cycle will be delayed until
switch current returns to a safe level.
If the EN/UV pin is low, the LT8610 is shut down and
draws 1μA from the input. When the EN/UV pin is above
1V, the switching regulator will become active.
To optimize efficiency at light loads, the LT8610 operates
in Burst Mode operation in light load situations. Between
bursts, all circuitry associated with controlling the output
switch is shut down, reducing the input supply current to
1.7μA. In a typical application, 2.5μA will be consumed
10
FB
pin with an
from the input supply when regulating with no load. The
SYNC pin is tied low to use Burst Mode operation and can
be tied to a logic high to use pulse-skipping mode. If a
clock is applied to the SYNC pin the part will synchronize to
an external clock frequency and operate in pulse-skipping
mode. While in pulse-skipping mode the oscillator operates
continuously and positive SW transitions are aligned to
the clock. During light loads, switch pulses are skipped
to regulate the output and the quiescent current will be
several hundred μA.
To improve efficiency across all loads, supply current to
internal circuitry can be sourced from the BIAS pin when
biased at 3.3V or above. Else, the internal circuitry will draw
current from V
V
Comparators monitoring the FB pin voltage will pull the
PG pin low if the output voltage varies more than ±9%
(typical) from the set point, or if a fault condition is present.
The oscillator reduces the LT8610’s operating frequency
when the voltage at the FB pin is low. This frequency
foldback helps to control the inductor current when the
output voltage is lower than the programmed value which
occurs during start-up or overcurrent conditions. When
a clock is applied to the SYNC pin or the SYNC pin is
held DC high, the frequency foldback is disabled and the
switching frequency will slow down only during overcur-
rent conditions.
OUT
if the LT8610 output is programmed at 3.3V or above.
IN
. The BIAS pin should be connected to
8610p

Related parts for LT3690