BD9870FPS_09 ROHM [Rohm], BD9870FPS_09 Datasheet
BD9870FPS_09
Related parts for BD9870FPS_09
BD9870FPS_09 Summary of contents
Page 1
Single-chip Type with Built-in FET Switching Regulator Series Simple Step-down Switching Regulator with Built-in Power MOSFET BD9870FPS ● Description The BD9870FPS single-channel step-down switching regulator incorporates a Pch MOSFET capable of PWM operation at 900kHz, enabling use of a smaller ...
Page 2
BD9870FPS ●Electrical Characteristics（Unless otherwise noted, Ta=25℃,Vcc=12V,Vo=5V,STBY=3V） Parameter Output ON Resistance Efficiency Switching Frequency Load Regulation Line Regulation Over Current ProtectionLimit INV Pin Threshold Voltage INV Pin Input Current ON STBY Pin Threshold Voltage OFF STBYPin Input Current Circuit Current Stand-by ...
Page 3
BD9870FPS ●Package Dimensions Fig.2 ●Pin Description Pin No. Pin Name 1 VCC 2 OUT 3 ※ OUT FIN GND 4 INV 5 STBY ※Normally OPEN www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. TO252S-5（Unit：mm） Function Input Power Supply Pin ...
Page 4
BD9870FPS ●Block Function Explanations ・ VREF Generates the regulated voltage from Vcc input, compensated for temperature. ・ OSC Generates the triangular wave oscillation frequency (900kHz) using an internal resistors and capacitor. Used for PWM comparator input. ・ Error AMP This ...
Page 5
BD9870FPS ●Application component selection and settings Inductor L1 A large inductor series impedance will result in deterioration of efficiency. OCP operation greater than 1.6A may cause inductor overheating, possibly leading to overload or output short. Note that the current rating ...
Page 6
BD9870FPS ＜Recommended Components (Example)＞ Inductor L1＝10μH Schottky Diode D1 D2 Capacitor C1＝10μF(25V) ：ceramic cap GRM31CB31E106KA75L(murata) C2＝4.7μF(50V) ：ceramic cap GRM32EB31H475KA87L(murata) C3＝OPEN ＜Recommended Components example 2＞…when the Duty ratio of output/input voltage is less than 10% Inductor L1＝10μH Schottky Diode D1 D2 ...
Page 7
BD9870FPS ●Typical Performance Characteristics（Unless otherwise noted, Ta=25℃,Vcc=12V,Vo=5V,STBY=3V） Input Voltage[V] Fig.5 Circuit Current vs. Supply Voltage：no load 1100 1050 1000 950 900 850 800 750 700 0 ...
Page 8
BD9870FPS 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.0 0.5 1.0 Output Current[A] Fig.11 Driver Drain-Source Voltage vs. Output Current Input Voltage[V] Fig.13 Output Voltage vs. Supply Voltage 6.0 ...
Page 9
BD9870FPS ●I/O Equivalent Circuit Pin 1 (Vcc, GND) VCC OUT GND ●Operation Notes 1. Absolute Maximum Ratings Exceeding the absolute maximum ratings (i.e. supply voltage, temperature) may cause damage to the device and make it impossible to determine the failure ...
Page 10
BD9870FPS 10. This monolithic IC which (as below) has P+ substrate and between the various pin. A P-N junction is formed from this P layer of each pin. For example the relation between each potential is as ...
Page 11
BD9870FPS ●Ordering part number Part No. Part No. TO252S-5 1.2±0.1 6.5±0.2 0.27±0.1 C0.5 +0.2 5.1 −0.1 FIN 0.71 0.27±0.1 0.6±0.2 S 0.08 M 0.27±0.1 1.27 0.08 S www.rohm.com © 2009 ROHM ...
Page 12
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose ...