X60003B-50_06 INTERSIL [Intersil Corporation], X60003B-50_06 Datasheet - Page 3

• Manufacturer Part Number: X60003B-50_06
• Manufacturer: INTERSIL [Intersil Corporation]

ABSOLUTE MAXIMUM RATINGS
Storage Temperature Range............ -65°C to + 125°C
Voltage on any Pin
Lead Temperature (soldering, 10s) ................ + 225°C
RECOMMENDED OPERATING CONDITIONS
ELECTRICAL CHARACTERISTICS
(Operating Conditions: V
Note:
V
V
I
V
TC V
ΔV
ΔV
ΔV
ΔV
V
I
V
IN
SC
Referenced to Gnd.............................-0.5V to + 10V
Temperature
OUT
OA
IN
DO
N
OUT
OUT
OUT
OUT
Symbol
Industrial
OUT
1. Over the specified temperature range. Temperature coefficient is measured by the box method whereby the change in V
2. Thermal Hysteresis is the change in V
3. Dropout voltage (V
4. Guaranteed by Device Characterization
/ΔV
/ΔI
/Δt
/ΔT
by the temperature range; in this case, -40°C to +85°C = 125°C.
T
The deviation between the initial V
in the Electrical Characteristics table.
OUT
A
IN
A
= 25°C; the X60003x-50 is then cycled between Hot (85°C) and Cold (-40°C) before a second V
Output Voltage
V
X60003B-50
X60003C-50
X60003D-50
Supply Current
Input Voltage Range
Output Voltage
Temperature Coefficient
Line Regulation
Load Regulation
Long Term Stability
Thermal Hysteresis
Dropout Voltage
Short Circuit Current
Output Voltage Noise
OUT
Accuracy
-40°C
DO
IN
Min.
Parameter
3
) is the minimum voltage (V
= 6.5V, I
(3)
X60003B-50, X60003C-50, X60003D-50
OUT
(2)
OUT
(4)
OUT
reading and the second V
= 0mA, C
(1)
+85°C
Max.
created by package stress @ T
T
X60003B-50
X60003C-50
X60003D-50
+5.5V ≤ V
0mA≤ I
-10mA ≤ I
T
ΔT = -40°C to +85°C
I
T
0.1Hz to 10Hz
OUT
A
A
A
IN
= 25°C
= 25°C
= 25°C
OUT
) into the X60003x-50 which will produce the output voltage (ΔV
= 5mA, ΔV
SOURCE
= 0.001µF, T
Conditions
SINK
IN
≤ +8.0V
≤ 0mA
OUT
OUT
≤ 10mA
COMMENT
Absolute Maximum Ratings indicate limits beyond
which permanent damage to the device and impaired
reliability may occur. These are stress ratings provided
for information only and functional operation of the
device at these or any other conditions beyond those
indicated in the operational sections of this specifica-
tion are not implied.
For guaranteed specifications and test conditions, see
Electrical Characteristics.
The guaranteed specifications apply only for the test
conditions listed. Some performance characteristics
may degrade when the device is not operated under
the listed test conditions.
reading is then expressed in ppm.
= -0.01%
A
A
= -40 to +85°C unless otherwise specified.)
= 25°C after temperature cycling. V
Min
-1.0
-2.5
-5.0
5.1
OUT
5.000
Typ
500
100
150
10
20
10
50
30
measurement is taken at 25°C.
Max
+1.0
+2.5
+5.0
OUT
900
150
100
300
9.0
10
20
20
50
80
OUT
is read initially at
) drop specified
OUT
1000Hrs
ppm/°C
µV/mA
Units
ppm/
µV
May 2, 2006
µV/V
is divided
ppm
mV
mV
mA
nA
FN8137.1
V
V
pp