P89LPC901 PHILIPS [NXP Semiconductors], P89LPC901 Datasheet - Page 32
![no-image](/images/no-image-200.jpg)
P89LPC901
Manufacturer Part Number
P89LPC901
Description
8-bit microcontrollers with two-clock 80C51 core 1 kB 3 V Flash with 128-byte RAM
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.P89LPC901.pdf
(55 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P89LPC901FD
Manufacturer:
OMRON
Quantity:
3 000
Part Number:
P89LPC901FD
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
P89LPC901FN
Manufacturer:
NS
Quantity:
1 000
Part Number:
P89LPC901FN
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Philips Semiconductors
9397 750 12293
Product data
8.12.7 Additional port features
8.13.1 Brownout detection
8.13.2 Power-on detection
8.13 Power monitoring functions
8.14 Power reduction modes
After power-up, all pins are in Input-Only mode. Please note that this is different
from the LPC76x series of devices.
Every output on the P89LPC901/902/903 has been designed to sink typical LED
drive current. However, there is a maximum total output current for all ports which
must not be exceeded. Please refer to
detailed specifications.
All ports pins that can function as an output have slew rate controlled outputs to limit
noise generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
The P89LPC901/902/903 incorporates power monitoring functions designed to
prevent incorrect operation during initial power-up and power loss or reduction during
operation. This is accomplished with two hardware functions: Power-on Detect and
Brownout detect.
The Brownout detect function determines if the power supply voltage drops below a
certain level. The default operation is for a Brownout detection to cause a processor
reset, however, it may alternatively be configured to generate an interrupt.
Brownout detection may be enabled or disabled in software.
If Brownout detection is enabled, the operating voltage range for V
and the brownout condition occurs when V
V
above V
2.4 V to 3.6 V. If the P89LPC901/902/903 device is to operate with a power supply
that can be below 2.7 V, BOE should be left in the unprogrammed state so that the
device can operate at 2.4 V, otherwise continuous brownout reset may prevent the
device from operating.
For correct activation of Brownout detect, the V
observed. Please see
The Power-on Detect has a function similar to the Brownout detect, but is designed to
work as power comes up initially, before the power supply voltage reaches a level
where Brownout detect can work. The POF flag in the RSTSRC register is set to
indicate an initial power-up condition. The POF flag will remain set until cleared by
software.
The P89LPC901/902/903 supports three different power reduction modes. These
modes are Idle mode, Power-down mode, and total Power-down mode.
•
•
BO
After power-up all I/O pins, except P1.5, may be configured by software.
Pin P1.5 is input only.
(see
BO
Table 13 “DC electrical
. If brownout detection is disabled, the operating voltage range for V
Rev. 04 — 21 November 2003
Table 13 “DC electrical characteristics”
8-bit microcontrollers with two-clock 80C51 core
characteristics”), and is negated when V
Table 13 “DC electrical characteristics”
P89LPC901/902/903
DD
falls below the brownout trip voltage,
DD
rise and fall times must be
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
for specifications.
DD
is 2.7 V to 3.6 V,
DD
rises
for
32 of 55
DD
is